Air Arms Utah Airguns Pyramyd AIR FX Airguns Daystate Diana Airgun Depot Edgun West Palm Beach Airguns DonnyFL: PCP Air Rifle Shop and Airgun Moderators The Pellet Shop Airforce Airguns
Saber Tactical Optisan Side-Shot Scope Cam NE Airguns Baker Airguns AGS Topgun Airguns Predator International Huben Airguns Huma-Air Shooting Supplies Hurricane Luftvapen AEA Precision Airguns H&N Impulse Air ZAN Projectiles Hawke Optics Stud Mag Loader RX Target Systems Sports Match Scope Mounts Altaros Banner CTA Thomas Air Hatsan USA Georgia Air Guns Skout Airguns Nielsen Specialty Ammo Patch Worm Weihrauch Sport Talon Tunes Airgun-Revisions JTS PARD ST7 PPP RTI AirStryk Industries Macavity Arms
  • D
    Lol, too funny!
  • D
    Right 👍 Too light a tube is also unsteady. If one would notice, my blowguns have either stainless or brass handguards to give them...
    • BF4C7967-842C-4AC5-AF33-3C39AD2C7EAA.jpeg
  • crowski
    crowski replied to the thread HW/Weihrauch HW30 walnut.
    I was talking to a sales lady Friday at AoA. I asked if they were sold out of the 30’s. She said they had lots. She would look into it...
  • J
    worked on a riser to use on the rails of my Fwb 300s and 602. It's more narrow than the forearm of either and will fit the front owl...
  • 357cal
    357cal replied to the thread Moderators.
    I use a Ronin on my .357 and a Yokozuna QD on my .308. Yokozuna is so much better and it's a tuner also.
  • kingfisher61
    Replace the flathead screw with hexheads. You'll never go back!
  • zx10wall
    What’s the length of the indoor “tunnel” range?
  • WoodWelder
    Looks to be a nice collection!
  • rc4fun
    Carbon tubes are hard to get smooth and uniform on the inside, I guess it could be done but not cheap.
  • Corvid_hunter
    Corvid_hunter replied to the thread Daystate Black Wolf.
    Yes. I haven't shot my Ghost as much as I would like, but it is a very nice shooting rifle. That said, I've been using it on the bench...
  • C
    coastal drifter replied to the thread N/A HW95 .20.
    I shot over the chrono again today, same tin of 11.42gr H&Ns 20 rounds H-748 L-728 AV-739 ES-20 SD-5 13.85ft/lbs. Reasonably...
  • Rondo
    This thread was hilarious. Thanks for the reset.
  • rc4fun
    If you haven't opened the case yet you might want to. I don't know about V2 but the v1 had a ckt board that plugged in. not often you...
  • .20calguy
    .20calguy replied to the thread HW/Weihrauch HW30 walnut.
    Well did you buy one?
  • thammer
    This listing has been renewed
  • M
    Long story short, I just found it funny a bit, at first I found a reticle similar to my reticle on chairgun but still looked off...
    • IMG-20250307-WA0162.jpg
    • Screenshot_20250307-184047.jpg
    • IMG-20250307-WA0163.jpg
    • IMG_20250307_165644_075.jpg
    • IMG_20250307_165729_204.jpg
  • Coinwa
    “If you want, I can crap in a box and mark it guaranteed…. I’ve got that kind of time.” ~ Thomas Callahan
  • markhooper
    I'm sorry this is not on topic but I just really want to know, what is the silver Beeman next to the HW 75?? I've seen the two tone...
  • Vana2
    Vana2 replied to the thread Exactly how many is too many.
    For decades I had one airgun, a FWB 124, that took care of all my needs. After 20 years of hard use, the piston seal failed and while...
  • Mr.H
    But it does have a life time warranty, unlike Vector or discovery. I know, cause I had one of those Chicon scopes that went south. My...
  • WoodWelder
    Oddly, Frank Zappa came to mind? :eek::ROFLMAO::ROFLMAO:
  • T
    Nice! I'm thinking carbon fibre? Yes...no?
  • .20calguy
    .20calguy replied to the thread N/A HW95 .20.
    It would likely have to be re-welded and re-cut. To me there's no excuse for Weihrauchs quality control to allow a part like that to...
  • Filter