Recent content by BBGunn

  1. B

    Fox Suppressors

    I'm using the 300 model on a 34fpe .22 rifle. The Fox suppressor is very quiet! It also comes apart easily for cleaning. I would buy Fox again if I needed another suppressor. It's all aluminum, inside and out, no plastic.
  2. B

    Vortex 2-7 rimfire vs Airmax Vantage 2-7 AO??

    I also like a low magnification variable for my 'woods' rifles. I have two of the Riton scopes linked below and love them! Good glass, side parallax/focus to 15yds, fine, open duplex style reticle and both my scopes have never lost zero. Check these out, you might find they meet your needs...
  3. B

    Airgun Technologies Uragan 2 rapid leak

    On my most recent repair I followed your advice and learned the hammer spring adjuster can be adjusted out past flush with the back of the block and still fit in my carbon stock. Prior to that I thought having the adjuster plug flush with the back of the block (stock setting) was as far 'out'...
  4. B

    Airgun Technologies Uragan 2 rapid leak

    Like WorriedMan wrote, it's most likely the valve poppet. My U2 .25 broke after about 2-months of use. My rifle has broken-down 5-times in 14-months of use. The first time it was the poppet body broke in half (pic). The other four times the o-ring that sits against the shoulder of the...
  5. B

    JTS JTS Airacuda "std" Custom is finally shooting fantastic !!

    Nice job! I love everything about that rifle! Why in the heck can't the manufacturers offer us a rifle like that? Instead they turn their engineers loose and we get 'Starwars' rifles!
  6. B

    Airgun Technologies Krale Listing Uragan 3

    You nailed it! I'll never buy from that jackass again!
  7. B

    Other AirForce Knockoff First Look + Other Pinty Guns

    What is thread size for the suppressor? I don't think it's 1/2-20???
  8. B

    Airgun Technologies Uragan 2 Things I've noticed

    I have a U2 .25 700 Carbon. I've tried all the popular slugs between 36gr & 44gr in my rifle. I've tried them at various reg. settings/velocities etc. Most accurate slug from my rifle is the AVS 44gr, .2513", Dish. Next best is the AVS 44gr, .2530", Dish. Third best is H&N 44gr, .2505"...
  9. B

    N/A Best value PCP?

    I think the answer to that question depends on the person wanting to buy the airgun. If you are not mechanically inclined you may find the answer will be different than for someone who can repair, or modify any airgun as required. For me, the best value airgun has been my Reximex Lyra. The...
  10. B

    A couple of generic questions about Dot sights...

    Despite what you may have read, 'red dot' sights DO have parallax error. You were correct when you wrote that dot sights were designed for close quarters use on large targets. The parallax error is small enough that the POI is irrelevant at close range for man-sized targets. If you are...
  11. B

    A New Wolf Rises

    The overall shape of the rifle is the same as the Epic Walnut.
  12. B

    Kral Arms Another parts gun.

    Love it! My kind of rifle! Nice work! Would be an excellent coyote calling rifle as you don't need many shots per fill.
  13. B

    Airgun Technologies Uragan 2 177 vs vulcan 3 177

    After I replied to you earlier I went and pulled the stock on my rifle. I turned the adjuster plug two full turns further out. My rifle has the carbon stock. I looked down into the stock and could see there is plenty of room for the spring adjuster to stick-out beyond flush. I put the stock...
  14. B

    Airgun Technologies Uragan 2 177 vs vulcan 3 177

    So, if I'm reading what you wrote here correctly, you are saying that you have adjusted your hammer spring adjuster farther out (less tension) than the factory setting (flush with block). Is that correct? To be honest, I never tried turning the adjuster plug further 'out' than flush with the...
  15. B

    Airgun Technologies Uragan 2 177 vs vulcan 3 177

    I am on the edge of starting to experiment with a light hammer spring, or shortened hammer spring. I have had my U2 for almost 14-months and have had to disassemble the rifle 5-times to repair one thing or another with the valve poppet. The latest was just 2-days ago. The first poppet body...