FWB mod 65

Cool, should have a screw hole underneath towards the front that will lockout the recoilless mechanism of you want it to behave more like a firearm.

I have a fwb80, no lockout ability but it's a fine pistol other than being a little awkward to cock for a 60 shot session.

What a great little pistol.

Really a fine pistol you're really going to enjoy that one. I have two. The top one Beeman called a Mk II, it has the shorter barrel. The FWB on the bottom came with the sporter grips that you have. I found the pistol a bit harder to cock with those, the grip tended to try to turn in my hand as I pulled on the cocking lever. So I ordered Rink target grips which is what you see in the picture. I do have to work on that gun to get the trigger adjustment correct.
They should shoot about 425 to 475 fps with 7.0 gr pellets. The several seals for it are readily available. When you cock it you'll see the (usually) blue compression seal. Below that you should see a small rubber bumper or damper. Make sure that is intact, it's important. There's much information available on the internet about how to reseal them. I've done it but found it pretty challenging, I find them to be a pretty complex pistol. Last one that needed it went to Pilkington's for the work. All that said they tend to just work without much attention at all. Really a fun and fascinating pistol, I'm sure you're going to enjoy it!

Jay

Sc0- said:

Cool, should have a screw hole underneath towards the front that will lockout the recoilless mechanism of you want it to behave more like a firearm.

I have a fwb80, no lockout ability but it's a fine pistol other than being a little awkward to cock for a 60 shot session.

Click to expand...

The hole needs both a screw and a plate the prevents the slide from moving.

The 65's are great MKI or MKII. They are the first in the line from FWB in the side lever recoilless pistols. Later came the 80 with 3 weights that can be used in unison, in any combination you choose or none at all. The 80 has and improved trigger over the 65's, later came the 90 which has an electronic trigger.

MKI

MKII with barrel weight

80 with all 3 weights

90

Wish I could find a M 80.

Sc0- said:

Cool, should have a screw hole underneath towards the front that will lockout the recoilless mechanism of you want it to behave more like a firearm.

Click to expand...

and you can flip the trigger weight to a PB setting of 1360g



...instead of a more normal airgun setting at 500 gram




I love the feel of the recoil less shot cycle, expect an average of 130m/sec (427 fps) from new or with a new spring installed

Edit: and JSB Exact 0,547g/8,44grain pellet

Love the pistol....and anything Feinwerkbau

Repair parts found here:
foest.europa

jaykb49 said:

The FWB on the bottom came with the sporter grips that you have. I found the pistol a bit harder to cock with those, the grip tended to try to turn in my hand as I pulled on the cocking lever.

Click to expand...

This will take the strain of your wrist:

Right hand holding grip
Support the barrel against left leg inner thigh
Left hand pulling lever

I was looking at a couple of those, and finally found a FWB80 which is in Fed Ex hands on the way.

Great find. I love my 65, just had it out today enjoying the nice weather.

I like the 80 I got last month. Not the easiest to cock but not bad. I am finding that I like the AV (IZH) 46m more. It has a much better trigger is easier to load, and that crazy cocking linkage is the easiest to cock.

The FWB 65 is only only air pistol I’ve ever owned so have nothing to compare it to. I’m thinking about picking up an ssp pistol like a fwb 100 series to go with my 65. Out to 10 meters my 65 is very accurate like I’ve read they all are.

I have an IZH 46m, a single stroke pneumatic. Fantastic trigger, mine is probably low single digit ounce range, 4-6 oz, accruacy, better than I will ever be and it has a wierd looking cocking system which makes it very easy to cock. I have learned about one little quirk, when you cock a breach block pivots up opening the breech end of the barrel into which you place the pellet. You then close the breech block, if you do not close it you will probably blow out and loose at least one of the two 0 rings that seal the system for firing. You can also dry fire it without charging the air cylinder. just cycle that breach block up and down and it sets the trigger. I got an aftermarket trigger that has a shoe that pivots to fit my finger, much better than stock which is still good. Canadashooting supply has them and they say an additional 12% discount which is not bad. Probably less expensive than a FWB 100 if you can find one. No problem with shipping one from Canada to the US either, at least mine came through very fast.

Well I now have a FWB 65 to go along with my 80, Now my son and I can have stand up matches with the same kind of gun. I may get a set of Rink target grips for it as it has the standard sporter grips, but will see how those feel first.

jkingrph said:

Well I now have a FWB 65 to go along with my 80, Now my son and I can have stand up matches with the same kind of gun. I may get a set of Rink target grips for it as it has the standard sporter grips, but will see how those feel first.

Click to expand...

Very nice. Eventually I’d like to pickup a couple more 65’s for the kids. Super fun for backyard target practice.

Just an observation:

I think your cocking lever pivot screw needs to be tightened as it appears to have worked it’s way down in such a manner that the pistol’s frame is being gouged.