American Air Arms Low powered Evol Mini tune

Anyone tune the Mini down to a lower power than the usual 28-30fpe they come at? I'm getting close to tearing into mine and tuning for the 12-14fpe range and was curious of anyone has a good reg setting for that. Doubtful anyone has but thought I'd ask. And if not I'll be letting people know lol. Mines at 2050psi at the moment and shooting at 30fpe. I'm thinking at least 1500psi would be where I should aim for. If not less.
 
Anyone tune the Mini down to a lower power than the usual 28-30fpe they come at? I'm getting close to tearing into mine and tuning for the 12-14fpe range and was curious of anyone has a good reg setting for that. Doubtful anyone has but thought I'd ask. And if not I'll be letting people know lol. Mines at 2050psi at the moment and shooting at 30fpe. I'm thinking at least 1500psi would be where I should aim for. If not less.

Extrapolating 30 fpe from a 2050 psi .22, I would say 1550 psi for 20 fpe, and, 1100-1200 psi for 12-14 fpe (1100 12, 1200 14, or 1150 for the best of both), provided you're trying to tune to the knee / 97% of the plateau.

Removing 800~ psi from the valve = 60-80 lbs less holding force, depending on the poppet diameter, which is a lot so you may need to add a stiffer valve spring (or pre-load it more with shimming) AND a lighter hammer spring, both not too difficult or expensive to figure if you tear into and do some simple calcs, and very reversible if you hang onto the stock units.

The OTHER option is just adding a choke to the transfer port. Say if you're currently ported to .165" or 75% of bore, you could somehow choke the port via transfer path with obstruction down to .085"-.09". No reg change + spring reconfig needed then, and no de-gas either more than likely.

-Matt
 
Last edited:
I'd choke the transfer path personally if you don't care for the shot count lower reg setting would provide, more work for the latter, but more shot count as well, less work for former, and no re-springing needed.

Your quest is why I modded my marauder to have a quarter turn valve, the VMS screw doesn't do enough with .225" porting and isn't super convenient requiring tools, where a quarter turn valve I was able to knock my power down from 40 fpe to 15 fpe in .22 on the fly without tools, I just lose the benefit of shot count which I don't care for on lower power.

-Matt
 
  • Love
Reactions: L.Leon
I don't know the math, but mine (.22) is shooting a nice solid 800+/- fps. As I recall, (it's been a couple of years) I may have done a small regulator adjustment. I have a barrel removal tool, and that's the only reason to have that. But without a gauge, I know that if I did that it was a "small" adjustment, so I didn't go too far, and have to pick it up again.
I should get it out, I haven't shot it in a while.

MIke
 
I don't know the math, but mine (.22) is shooting a nice solid 800+/- fps. As I recall, (it's been a couple of years) I may have done a small regulator adjustment. I have a barrel removal tool, and that's the only reason to have that. But without a gauge, I know that if I did that it was a "small" adjustment, so I didn't go too far, and have to pick it up again.
I should get it out, I haven't shot it in a while.

MIke

800 Fps with what weight projectile? 15.89 puts that around 23 fpe, and 18.1 around 26 fpe, a bit higher than Dillon is interested in afaik.

-Matt
 
There's no valve return spring...
I had to go to a reduced transfer port(needs to be made), a lighter hammer, lighter spring,, AND lower the reg to get down to 20 ft lb and later, 12 ft lb.. For mine to run well, 12 ft lb is 1400 psi... 20 ft lb is 1700 psi...
This is for 177. For 22, a lower pressure might be necessary but the valve depends on this pressure for closing...
You might be able to get close to 20 ft lb by reg and hammer spring adjustment alone but I'd be very surprised to see you get below that.
A query to Tom might yield some parts or info or both if he has a moment to respond..
Bob
 
  • Like
Reactions: Stubbers
There's no valve return spring...
I had to go to a reduced transfer port(needs to be made), a lighter hammer, lighter spring,, AND lower the reg to get down to 20 ft lb and later, 12 ft lb.. For mine to run well, 12 ft lb is 1400 psi... 20 ft lb is 1700 psi...
This is for 177. For 22, a lower pressure might be necessary but the valve depends on this pressure for closing...
You might be able to get close to 20 ft lb by reg and hammer spring adjustment alone but I'd be very surprised to see you get below that.
A query to Tom might yield some parts or info or both if he has a moment to respond..
Bob

The more you choke a port, the more the power can be reduced to the point of 0, so you don't HAVE to run less reg, it is very much an option, but definitely a good one for increased shot count.

-Matt
 
  • Like
Reactions: Arzrover
Lol so not as simple as I thought. Don't think I can do the TP that's a complicated piece. Guess I'll need to think about it more.
You can add a restriction into the existing tp with a very mild adhesive that heat would remove. Just need a tube with the same OD as the current tp ID and then have the new tube ID be around what I suggested above, give or take.

-Matt
 
  • Like
Reactions: Arzrover
Just to add a few other ways to skin the cat....

1) Limit poppet travel, throat then becomes the choke as the poppet can only lift so far off the seat, cutting dwell and possibly air flow
2) Assuming balanced valve, check if the vent is adjustable, if not (Tom would know), scrap the idea.
3) Severely reduce the plenum volume
4) Choke at the valve inlet

All the above can be done while being reversed if the approach is mindful enough.

-Matt
 
It's not hard to get into these to change the regulator setting. Simply de-gas with the burst disk, remove the barrel while it's exhausting the air, and take off the front cylinder cap. This gives easy access to the regulator adjuster with a long tool. I used a hex bit attached onto an aluminum arrow shaft for a permanent adjuster tool. I also drilled out an access hole behind the rubber butt plate this allowed me to get at the hammer spring tension adjuster without having to remove the chassis each time I want to make a hammer spring adjustment. The same arrow shaft has a bigger 5/16" hex on the opposite end for this.
 
So I decided I will just make this gun my 20fpe gun I wanted and make my Vet Short my 12fpe gun when needed. With the DonnyFL speed dial it actually is very simple to change between my tunes. I tuned the Short to 20fpe but will just swap them for my needs.

As far as the reg and all that I've adjusted them before. I tuned my prior 15" to 30fpe instead of 44fpe. Dropped reg I think to 1600psi. Pretty simple to do. I like the idea of goin in from the front with a tool to adjust while in the tube. Especially how short the Mini tube is. I'll probably shoot for that same pressure based off Matt's calculations of 1550psi for around 20fpe.
 
I did, at one time, have an Evol Mini I tuned down like that. I don't remember the exact fpe, but I tuned it for Crosman 14.3s at around 700fps, IIRC. I recall dropping the reg down to something like 1400 psi and then just adjusting the hammer spring. I didn't muck with the TP and my recollection is that it was quite consistent. The one problem I ran into was that I had to back the hammer spring WAYYYYY out and it made getting the lower frame back on tricky as it was hard to get past the hammer spring screw sticking way out the back of the receiver.

So it's all possible, but a lighter hammer spring is recommended.
 
800 Fps with what weight projectile? 15.89 puts that around 23 fpe, and 18.1 around 26 fpe, a bit higher than Dillon is interested in afaik.

-Matt
Matt -

While I use varying pellet weights during any given session, I do my adjusting on all of my adjustable guns with 18.1 gn pellets. Either FX or JSB.

Wow, slower than 800fps. That's getting down there. Seems that most of the high end shooters comment that below 800fps is getting below any good accuracy with most all pellets, in most all guns.

Mike
 
  • Haha
Reactions: thumper
Unless you are talking about longer distance (ie: 100+y), setting an 800fps boundary is utter hogwash. I've never seen anyone anywhere post a number or comment like that. I've got - and so do plenty of others - tunes that range anywhere from 600 fps to 750 fps for lower power tunes - and they've all been very accurate out to 50 yards. Heck Olympic quality 10m pistols only shoot around 500 fps - can you tell me that they aren't top tier accuracy.

As long as you are tuning within the design constraints, accuracy and consistency should not be a concern.