JTS First Problem with the "Cuda"

Jump to latest Follow Reply
Chief Ten-Beers

Chief Ten-Beers

Member
May 1, 2024
1,142
1,667
So, I have been leaving My rifle Connected to My tank and added air as needed. After the bottle reached My desired PSI I just left it hooked up to the Tank. It's been hooked up for about 4 days. I shot the Tank down to about 2000 psi and said, time to top the tank off again. It has turned pretty chilly here and the Rifle, tank and all were very Cold. So I went to disconnect, I relieved the Pressure from the Fill whip and air started coming out of the Fill nipple on the Rifle. Just wondering if anyone else has had this problem? Could the one way Fitting just be too cold to close all the way? I brought it in so it can warm up and then I can try putting air back in and see if it holds. Just wondering if others have had a similar experience?
 
  • Like
Reactions: Bert928GT
Chief Ten-Beers said:
I will try that after the rifle gets to room temp. The air is just about done leaking, so I will keep that in mind. Thanks!
ETA It's the Male fitting.
Click to expand...
I've fixed a similar leak with a drop of silicone oil on the male fitting before putting air in it. Could help.
 
  • Like
Reactions: ToddGeddes63 and Chief Ten-Beers
Upvote 0
Dairyboy said:
I've fixed a similar leak with a drop of silicone oil on the male fitting before putting air in it. Could help.
Click to expand...
I tried the Oil trick, I put some in the Male as well as the Female. It didn't work at first, but then I tried bleeding the line pressure from the Tank quickly a couple of times, at first it slowed a little, the second time, a little more, 3 times and now it does not appear to be leaking. I have shot hundreds of rounds since I last put oil. I was a slacker! Thanks for the Tip!
 
  • Like
Reactions: rcarlisle and Dairyboy
Upvote 0
Firewalker said:
When you press the check valve open for long periods of time, the valve can stick.

A wooden match stick can often bump the stem loose so it can fully seat.
Click to expand...
It's working properly now, but now I have the same Prob with the Female on the Fill Hose. I wasn't aware of that until I refilled the Tanks. I need to fix that one now. Lesson Learned, disconnect tether after shooting.
 
  • Like
Reactions: ToddGeddes63, beerthief, Firewalker and 2 others
Upvote 0
Chief Ten-Beers said:
I tried the Oil trick, I put some in the Male as well as the Female. It didn't work at first, but then I tried bleeding the line pressure from the Tank quickly a couple of times, at first it slowed a little, the second time, a little more, 3 times and now it does not appear to be leaking. I have shot hundreds of rounds since I last put oil. I was a slacker! Thanks for the Tip!
Click to expand...
Awesome to hear!
 
  • Like
Reactions: Chief Ten-Beers
Upvote 0
Chief Ten-Beers said:
It's working properly now, but now I have the same Prob with the Female on the Fill Hose. I wasn't aware of that until I refilled the Tanks. I need to fix that one now. Lesson Learned, disconnect tether after
Click to expand...

Chief Ten-Beers said:
It's working properly now, but now I have the same Prob with the Female on the Fill Hose. I wasn't aware of that until I refilled the Tanks. I need to fix that one now. Lesson Learned, disconnect tether after shooting.
Click to expand...

I'll teather for the session but I would not keep the fosters connected long term.
 
  • Love
Reactions: Chief Ten-Beers
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu