- O
Air Arms Pro Sport Caliber Change?
Right hand thread.Steve!- Ozwald
- Post #8
- Forum: Traditional Airguns
- O
Air Arms Pro Sport Caliber Change?
It is not hard to do, the shroud is the hardest part trying to remove it from the barrel use lots of heat. the nut comes of pretty easy the right socket and an extension and a padded vice will do it. good luck. Steve!- Ozwald
- Post #6
- Forum: Traditional Airguns
- O
Air Arms Pro Sport Caliber Change?
I can change from 177 to .22 in about half hour. Steve!- Ozwald
- Post #4
- Forum: Traditional Airguns
- O
Air Arms Evening Gents!
Try and pull that little buffer button on the bottom of the barrel , I had a problem with it sticking into the barrel too far and was clipping the pellets on my tx. Steve!- Ozwald
- Post #34
- Forum: Traditional Airguns
- O
What springer did you shoot today?
They seem to be for me, but not much.Steve!- Ozwald
- Post #4,344
- Forum: Traditional Airguns
- O
What springer did you shoot today?
That is the colour of the tin, I have some in red tin and some in green tins.- Ozwald
- Post #4,342
- Forum: Traditional Airguns
- O
What springer did you shoot today?
I found a pellet my tx and pro sport like,Got a chance to try them today.Steve!- Ozwald
- Post #4,335
- Forum: Traditional Airguns
- O
Shooting tube Post deleted by OP
I have heated workshop and shoot there all winter with my pellet guns keeps me out the house.lol, The ground slopes up away from my shop so the other end is about 8' under ground.I made a frame up with a 3/4" steel plate at the back and a couple of rollers on my lathe to fit a roll of meat...- Ozwald
- Post #19
- Forum: General Discussion
- O
Shooting tube Post deleted by OP
I used 18" culvert for my under ground 30 meter range. the lights are for my chronograph. Steve!- Ozwald
- Post #17
- Forum: General Discussion
- O
Tuning Where do you work on your airguns?
This is where I hide. Steve!- Ozwald
- Post #49
- Forum: Traditional Airguns
- O
What’s your daily job?
I was a plumber, gas fitter, fibre glass pipe fitter, welder, and I still have dripping taps at home. lol. Steve!- Ozwald
- Post #130
- Forum: General Discussion
- O
HW/Weihrauch HW55 versus HW98
I love that butter bit,lol, sounds like my wife in the morning.lol Steve!- Ozwald
- Post #8
- Forum: Traditional Airguns
- O
Air Venturi ENTER to WIN the Air Venturi Avenge-X and much more!
in- Ozwald
- Post #1,004
- Forum: PCP Airguns
- O
What springer did you shoot today?
Shot my pro sport today,177 at 900 fps with 7.9 cp hp. I didn't,think it was to bad for 76 year old eyes. what do you think. I know there are a lot better shots than me on this site. Steve!- Ozwald
- Post #3,222
- Forum: Traditional Airguns
- O
Air Arms AA Prosport owners…
I do not have any pictures right now and I did not want to take the rifle apart for a picture, yes I put brass buttons on the trigger block to centre it. I did it in my lathe and made it a slight push fit and that stopped the rubbing. I also put the piston in my lathe and checked the run out on...- Ozwald
- Post #72
- Forum: Traditional Airguns
- O
Air Arms AA Prosport owners…
Mabe check the inside of the trigger group where the latch rod connects to the trigger, on my pro sport it was touching the top of the hole when it was installed because the hold-down bolt would pull it down. So I did button the trigger group, stopping it from touching when reassembling. you can...- Ozwald
- Post #70
- Forum: Traditional Airguns
- O
Beeman Calling out A.G.R. !
That is fantastic work. steve!- Ozwald
- Post #20
- Forum: Traditional Airguns
- O
Air Arms Open sights on pro sport
- Ozwald
- Post #8
- Forum: Traditional Airguns