Search results for query: *

Many, while far from all, of the Turkish made guns run semi tight rifling twist, which is what slug guns thrive on. If there´s one brand that truly is garbage out of the box it´s the early Turkish made Aselkons. However. That there is an Aselkon MX-10 that got a decent sized plenum tossed...

I´d say this is a matter of balance. To my findings very much can be had by altering that power adjuster. Get or make one that in essence will close the shutter completely, and just open ever so slightly at full. Point being that such a restriction is a constant and should to greater avail hand...

@ Graycrait. The ones i´ve been into for instance have a valve out of a material that´s got to be recycled Coke cans from far east Asia. Cough at it and it´ll strip threads and what not. Barrels are decent though, but the general build, IMO, is juuuust to keep the thing together. Fact is, i´ve...

Went down that route many many moons ago. Back then the max we were dealt was the 25.4 Knockouts. Had them running just up to the wall, so it sure can be done - yes even on the stock barrel length. But truth be told, the Stormrider is a rather weak design all said and have sure moved on since...

@ Derick. What do you want to know? For the most part enlarging the so called transfer ports, which entails the exhaust port on the valve and the barrel entry too, is rather straight forward. Just use a drill bit of choice and common sense. The drill bit to rest though... follows what´s just as...

Ontopic Got one of those. The AR-6 is mentioned above, this is from before they turned Evanix. Sweet little revolver rifle, have to say. Shoots very well when i feed it pill by pill. For some reason groups opens up a tad as soon as i use the revolver mag for whatever reason. Need to look into...

22 caliber. 30 meters. Done with an unregulated Hatsan Nova. 10 shots. Opening at its largest 6,8mm. Pills, regular JSB Knockouts right out of the tin.

With the working parts of the reg out of its hole, looks deep in there with the trigger and what not removed of course. Close to the bottom of that hole there´s an o-ring, and when an Impact leaks out of the bleeder hole i´d say 9 times out of 10 it´s that o-ring that´s gone bust. As mentioned...

...picking 2 or 3 Kral mags up and set the main block on the mill of mine and be done with it already. None the less. The Meta Premium is an absolute *rapload of gun for the money. Sans flaws then? No. Of course not, but the thing is they can all be handled - which is more than can be said for...

I believe so, yes. Check with FX or Utah though.

Hm. A while back i went ape on the cheapest POS i could find, in 177cal. In the end i came to settle on H&N´s 20 grain hollowpoints and the thing tossed them well into supersonic with no ills observed (just shy of 1300fps) I bet this could be juiced up even more will be but.. What i´m saying is...

...you could use the reg pressure gauge for entry port, it just needs to be enlarged somewhat at the seal for use as entry. Gauge port is on thread M10*1mm Me, i´m always conservative as *ell when it comes to pressure vessels in as much that i basically use steel only, and then high pressure...

I'd say 40fpe is rather simple. Maybe 55fpe to be wrung out of it sans any heavier efforts such as a plenum

...rather old design by now, the BSA R-10. This one in 177cal. Seeing its age it´s rather cumbersome to the build but that being said one thing´s for *amn sure and that´s that the design was never intended for any higher horsepower applications. Thus what i did was fab me a rather "small...

Relax a tad boys. The Benjamin Gunnar is simply a rebranded Reximex NYX. Smaller stuff might be different, but on a general whole.. Reximex NYX The NYX/Gunnar is one of Rex later designs. Want to mention this as one of the others by Rex right up there is the Meta Premium. Which in turn IS a...

I routinely replace the PA on both Kral and Rex guns. This of course to cater to larger transfers, while keeping some sort of resolution on the power adjuster. I would vote against "just drilling the hole out". Use a reamer, plenty of fluids and remove chips often. If reamer dia is close enough...

Scope is just a rather old regular Yukon Photon 6.5 IR. Making a 100cc plenum for the Throne, as i view it, what´s needed is a lathe so you can cut the threads for the end caps on it. As is i used steel only on this one.

Depends on if out of the box or with porting added? If porting, this thing in 25 incl a 2mm stem poppet and so on will hand inxs of 100fpe without even breaking a sweat, and yes somewhere around the 1000 mark me believes. The Reximex Meta Premium. Sports a 90cc plenum and a 700mm barrel right...

To my knowledge Reximex sells barrel kits. As for if they do in the US or UK, no idea. What they don´t sell though, pity to say, is 100cc plenums. Them you´ll have to make yourself.

Yep. Measured height. Added 1/10mm and turned a new one, massive press fit, on the lathe