Search results for query: *

I picked up two as well. Very nice, and heavy duty to boot!

Must admit I have been very impressed with my .25 max. 👍 100yds moa groups are possible.

Thank you RWSx3 for your input. Sounds like they may have stiffened up the forearm on the dreamline models. I have a very nice DL walnut .177 that shoots beautifully. Rather than swap out barrels, I was thinking of getting another DL in synthetic in .22 or .25. Thus increasing the depth of...

On the synthetic Streamline models of a few years ago, some complained that the forearm of the stock was not very rigid and was some what flexible. To those that own a Dreamline classic synthetic, has FX stiffened up the synthetic stock on the Dreamline classic? Thanks for your input.

Must admit. I'm enjoying mine as well. It's not a long range competitive rifle, but for a basic hunting gun out to 75yds....fits my bill fine. 👍

I got a bit busy with farm chores so have not reported back on my Max .25 status. Apologies. Travis did send me the new phenolic block. Had to dremel out the attaching screw counter bore just a bit, but got it all mounted, the stock put back on and away I went. This gun keeps impressing, the...

I did read the post. TY. I have tried to drop the velocity a bit by backing out the HS. Long story short, to get down into the 850fps range with 25.4gr required the HS be backed out 2 full revolutions. This unfortunately now causes the HS screw to extend beyond flush with the back of the...

I was waiting for the other shoe to drop, and you admit the fella was you? 😉 how u doing bud?

That is very impressive!

We will see if all the hype is worth it after I get the scope mounted....pessimisticly optimistic 😉 😆 🤣 this is so much fun! On a more serious note, did you adjust the reg or hammer spring or both?

Got my JTS Airacuda Max this morning. I must admit I was anticipating a certain amount of disappointment. $420.00 for a regulated airgun? Don't get you hopes to high buddy..... I'm not a pessimistic person by nature. Actually just the opposite, I really try to find a positive in everything I...

Ok, just finished shooting the JTS .25 DEAD CENTER 25.4g in a second .25 cal gun that I have. Unfortunately I experienced the same very tight entry into the breech. When I say tight. I mean too tight! Sad to say these pellets are not going to be used in any of my guns. With that said, the...

PA PYRAMYD AIR treated me right. I had a complaint about some pellets that I just purchased. Henry was courteous, honest and willing to make things right. So if you call customer service and get a "bitc*y" rep, hang up and call someone like Henry! Thanks PA.

Unfortunately not, it was raining and windy, I didn't feel too compelled to take any pics. I did shoot other JSB and FX groups for comparison. After reviewing my notes, I would say the knod went to the JTS, out of a 10 shot group at 100 yds on painted steel 5 of 10 were "touching" in so...

I'm going to try the .25 JTS in another gun today. I'll report back after I do. I took some micrometer measurements of the JTS .25 and really didn't find to much discrepancy in the dimensions.

The .22 JTS DEAD CENTER are great! Clean, load well and group well at 100yds.

Got my .22 and .25 JTS DEAD CENTER PELLETS in hand. I am impressed at how clean they are! Unfortunately the .25 are tight in breech in the one gun that I have shot them. Not real happy about that, as I'm sure I am probably wearing out my breech probe O-ring. The issue with the .25 is the...

If your supply drop to 160b and 150b, and your reg psg reads 210 after you have shot several shots, I would assume your reg gauge is bad. The reg pressure can't be higher than the supply (tank, tube) pressure especially after you take several shots as I described above. You can fill your...

Got it to work, but there appears to be an insurance charge of approx $8.00 on a $400.00 purchase....no big deal. Nice going UA! Thanks!

Mine is just shy of 140bar. As from factory. .25 bobcat mk2.