Search results for query: *

I recently blew a burst disc on my Yong Heng compressor. Despite replacing the disc multiple times, I'm getting a leak around the threads for the burst disc assembly. I've changed the amount of torque applied, but no dice. Apparently, these things can crack, so I have another on order. In the...

On the Dreamline, there's a screw above the transfer port. What type of sealant should I use to prevent air from escaping around it? I tried thread tape, but I can still feel air around it when I fire the gun. Thanks.

I have a set of Tekton wrenches that gets the job done. The problem is that they're long, which can make unscrewing gauges awkward. I also have set of their stubbies, but they don't make them in large enough sizes. Is there something better? Thanks.

Been trying to source a replacement for my Dreamline Classics' regulator gauge: 23mm, 200 bar range, black face, chrome finish, FX branding. Utah Airguns only has one in stock, apparently. Anyone know of another store that might have some? Thanks.

On the Dreamline, there's a grub screw on side opposite the power adjuster. It fits into a slot on the power adjuster assembly and prevents unwanted movement. I'm talking about the small screw on the bottom of this picture: Should I be screwing this thing in until it bites into the power...

Just to verify, which direction is the valve seat supposed to be oriented? I assume it's the first, but I'm narrowing down a leak and want to make sure, so I don't have to crack everything open again. Thanks.

I'm still chasing my Dreamline leak. I put my finger over this hole on the power plenum and felt air: I figured it's a regulator leak. I actually have a second fully assembled power plenum, so I put that one and gassed it up. Same leak! Am I unlucky enough to have two leaky regs? Is there...

According to the parts list I have, it's a small plastic washer. However, I contacted Utah Airguns, and they said the washer was switched out for an x-ring. I picked up some x-rings, and while they create a good seal, they make the gauge stick out a bit too far. This, in turn, causes the dust...

I recently purchased a valve removal tool. I'm trying to avoid damaging anything, so I want to be crystal clear on how to use it. Is the screw on the end intended to catch on the edge of the valve seat? There's a video of someone using it, but I'm not entirely sure what they're doing. They're...

I have a check valve between the small gold filter and air tank. Today, it started leaking between the check valve and quick disconnect on the gold filter. I figured it was the o-ring on the disconnect. Sure enough, it was damaged, and I replaced it. The problem persisted, so I tried switching...

Here's the deal: I have a .22 Dreamline Classic with a 500mm barrel. The regulator is set at 100 bar. I'm shooting 18 grain pellets and would like to get near 900 fps. I suspect I'll need to slow things down to achieve optimal accuracy, but I'd like to hit 900 to give myself more space to work...

For advantages, I'm thinking of things like improved friction. AFAIK, the stock Dreamline Classic hammers are made from a material other than brass. Thanks.

Up for sale is this Optisan scope. This light and low profile scope is perfect for someone that dislikes top heavy setups. There's three points of damage that I can find: a scratch on the tube, some pits on the scope caps, and the "Made in China" sticker is peeling off. The scratch is from me...

I'm wondering if the material they use would get along with softer materials like wood or laminate. Most of the pictures I've seen having them being used with polymer stocks. Thanks.

I've been battling wandering POI after storing my Dreamline overnight. It's calmed down over the past few days. Maybe I tightened some things that needed tightening while troubleshooting. Anyway, I ended up buying a carbon fiber liner sleeve. The current set-up is a bushing at the breech end...

Was shooting my Dreamline after remounting the scope when the accuracy suddenly tanked. I took it back inside and took off the moderator to inspect it. Sitting where the moderator threads into the barrel was a small black piece, maybe 6mm at its' longest point. I took apart each magazine and...

I have a Stikman attached to an SCBA tank. When not in use, I connect the fill whip to the foster fitting on the fill station. I also open the bleed screw. My reasoning is that if the valve on the tank springs a leak the air will harmlessly exit through the bleed screw. Any problems with this...

I'm been looking for a small, flat brush to apply moly. Was hoping for something with a cap so I don't get grease over everything when I'm not using it. Any ideas? Thanks.

I have one of those small gold filters by Creation Core. The large o-ring on the cap is slowly falling apart, and I'd like to replace it with something more durable. Maybe some Buna 90s. Does anyone know the exact size of these? There's also a small o-ring inside the quick disconnect that I'd...

I'm going through the process of ordering some o-rings. Everything has been easy enough to source from Oringsandmore. Finding Buna 70 13.95 x 2.62mm o-rings, however, have been difficult. These ones are close but not ideal. Anyone know of a reliable place I can easily get some of these? Thanks.