Search results for query: *

I can't be of too much help both mine are ,177 one stock tuned for 8.44 and the other with a chokeless bsa bbl tuned for 15,4 slugs and 13,43 redesigned. The HW 100 is a great rifle. It doesn't waste a ton of air after you have it tuned I generally go for as low a reg pressure as I can and...

Honestly drag a patch worm through it,,, load up on jsb exact heavies,,, scope of choice,, mine has a dedal 6x in red laminate...and shoot.... I did adjust trigger a bit.... nothing else to do if you want to shoot heavier just turn up to about 890-910 and shoot...mine does 30mm groups at 100 m...

I am about 99% sure your trigger over travel stop screw needs about 1/16 to 1/8 turned out your hammer is hanging on the sear edge

I'm hoping the r5m is in it's synthetic chlothes...mine has been a tank in that pattern....

Yeah the bbl is shoved back into the receiver...this is super common when wildcats are shipped... If you look on YouTube for wildcat bbl installation it will be obvious https://youtu.be/VzOx7jQ2bMo

No on the mag well not easily, except to trade it for a410. But the power adjust should stay put sounds tkie friction ring is loose or shrunk

Find a huntsman in .22 easy to hand pump,,, get it unregulated and shoot it's curve and learn it! You'll have it forever and only be topping not killing yourself filling it.... plenty left over to buy a thermos bottle and folding chair to take a 20 min break after pumping up before you will be...

I have both as well and It is a coin toss...the uben trigger is just ok in a different way I can soot both equally well... My lcs was a leaker initially. But is ok now... It shoots beautiful but so do my hubens I have a 2 and a 5...

Right on!!! Air should be pretty clean and dry... Correct lubricant for the seal material is a must...other than breech seals I have been shooting pcps since 83 and never had leaking problems... I can tell you that the first theoben rapid 7 in the us is still only had breech and bottle seal...

what you will have will probably hold honestly till you use the degas screw again, the disk I mention is just to form a fresh conformable seal seat for the ball and fills in any irregularities in the ball seat. If you get sealing seat too wide in HPA applications you loose the seal very often ...

I have used a bat on a lelya .25 and on my .22 matador and it is a very nice addition. I haven't run on a .177 but it is a very nicely made extra bit and the volume bump would probably be noticeable to others around but I doubt to the shooter much... I don't notice the difference on my matador...

Literally out of the box Tie between Lelya 2,0 in ,25 Wildcat mk2 compact ,25 Uragan ,22 Oh and from a few years ago fwb 300s but you don't care about that one....;-)

I've been playing with the small slugs as well and have gotten 960 980 easily out of the 15,4 with a r5m and let poly bbl unchoked ,1778 dia slugs...they have a few good speeds I noticed slow like 830 gave good group,75 at 47yds and fast 905 915 again ,7" at 47 and again at about , 960... I...

If you get this seat too wide it will not seal any more... Do this I think it is a 3 mm ball get a 3 mm I'd piece of tubing brass from hobby shop and cut a disk out of,025" thick nylon 6 sheet from McMaster Carr and drop in hole flat add ball and grub screw don't tighten up more than needed to...

link to a few notes from a limited test https://www.airgunnation.com/topic/edgun-45-mm-slug-does-it-work/

Note to help you all out, Matadors and all edguns are not set up for slugs!!! They can be, they need to be at the least throated and this does not hurt pellet performance if done correctly. their straight push feed system does not have a ton of mechanical advantage for bullet seating, so the...

Not by Ed, ie no additional treatment like the s510 and the like get, but they are spec. stock from lw.....now some are going to be coming from Alpha when ??? and what cals.??? so far Ed has said .25 and maybe .22 for home market.. from what he has shown he is content with them. I was in the...

Last details from bbl. You may want to know. The effective groove was ,1805" and effective land or bore was ,1775" slightly tight compared to let specs but my shadow graph may be slightly out... Hopefully this helps any one wanting to do small bore slugs

Oh bbl details I forget to include, 11 degree recessed crown. And it's a slower twist 1in 17. And the blank was a,471 od the threads are m12 x 1,25 each end. 1" cut from breech this is the stamped end and the rest taken off the muzzle end of the 23" blank,,, Reamer was homade single flute...

Possible , gotta keep the edgun stuff cryptic 😂. And wierd. Could not resist