Search results for query: *

My tune is irrelevant. There is a very good chance my tune wont work for you. Every barrel/liner, valve, springs used in the entire system that effect the firing sequence are different. So its very unlikely my tune will produce what you want. If you are going to try and get the most out of your...

I 3D print stuff and the only possible issue I see with mounts would be the stability. I cant say for sure but I feel like dimensions will change with temp and moisture. I know temp will do it and filament absorbs moisture. Air guns dont have enough recoil to be an issue but the possible...

Whats the size and what material exactly would it be cut from? You mentioned plastic but what plastic or does it matter?I recently bought a laser prob 3 months ago. I have cut out quite a few things similar to this. I did a bunch of xmas ornaments as well as some engraving. A Co2 laser could cut...

That would be easy to cut with a laser.

For punching paper 25x and up. I only have a couple scopes that max out at 15x or 18x but they are on big game rifles. I use 25x -60x at 50 yds when shooting my airguns or rimfire rifles.

I cant remember the exact year they came out with the spin loc tanks with the built in QD fill. Is it the spin loc tank? If so its the same as all other QD airgun fittings like FX, daystate and others use. If its the original tank you need the airforce fill adapter.

I set all my FX barrels on slug port. The only exception being if its gonna be set up as a low power rifle in the 12 fpe range. I have never had any issues with damaged pellets or mis feed from using the slug port.

I would pull the barrel and see if that frees it up. If not at least you might get a little easier access to the stuck pellet for easier and safer removal. If the second pellet lodged into the skirt of the first removing the barrel should pull it out with the barrel.

.25 cal? Get the 16 twist if you are talking .25.

Really? I live in Hamilton on the west side and if I buy a gun in bob wards they walk that to the front. Last time I bought 22 LR ammo they didnt walk it up front but thats been awhile. I order my pellets, rimfire and load all my other ammo so I never buy in store these days. Maybe its changed...

Non its fine. All you need to worry about is if the hammers energy is too low causing a larger jump than you want. Thats based on personal choice and how you want it to perform. I usually like to see 10 fps or less jump since my tunes hold single digit easily with regulated rifles. That way if I...

Depending on how far down from the reg setting the hammer energy is at will determine how much jump you see when the pressure drops of the reg setting.

Yes the speed increase at the end is the balance between the hammer and tank pressure. Being tuned on the knee will cause the increase. So as an example if the hammer energy is set to fully open the valve at 1800 psi and the reg is set at 2000 psi you will see velocity increase when the pressure...

No if you have your rifle tuned correctly higher reg pressure will lower the velocity not increase it. You should be tuned on the knee of the reg setting. Meaning the hammer doesnt have enough force to fully open the valve. So if the reg creeps up its going to open less causing lower velocity.

On my firearms I bore sight by looking down the barrel. Then I shoot one shot onto the target. Then I just hold the rifle on the poa for the shot and adjust my turrets to bring the reticle to the hole. Then I shoot a group to finalize the adjustment. I do the same with my airguns but most cant...

H&N Heavy 38 gr. & 40 gr. shoot the best in my FX liners.

What size did you get .217 or .218? .218 works in my FX liners and it seems to be the preferred size in FX liners for most.

Yes. I have a range setup on my property for airgun and rimfire.

Both 700mm.

Thats not the symbol for euro its for pounds. Whats the rate show when you use the correct currency?