Search results for query: *

Not exactly my first rodeo, been doing the 25s and up that way for quite a while. Works rather well, but in all honesty to a large degree depending on caliber.

Nope. Not even close.

I own an AR-6 and as i work on guns.. might be able to hand a bit of insight. If there´s anything specific, just ask. Yes. Barrel is threaded to the main block via a M12*1 thread. This is also where you set end gap. Ie; turn the barrel in until the cylinder can´t be rotated by hand anymore and...

Wow! :eek: That one BUMPY ride! For friggin AIRGUNS?!?!? Well. For hunting small an possibly smaller mid sized.. as an entry gun that won´t break either you or the bank? Know you don´t get ´em all over the US, but they ARE there to be found.. and are certainly imported to Canada. Hear me out...

True. Most do though, with a bit of detective work invested. These days most of the both Chinese n Turkish crop guns offered run at least semi fast twists at the very least, which from a twist aspect will work with most commonly available slugs. However. As you bring up, and ain´t that the...

You measure the diameter of the pill shoved through the bore to get an exact measurement of what grooves n lands tell. Now. For a gun sporting a choke this means that you first up remove the small o-ring within the breech, that´s there to seal vs the probe. This just not to ruin it as you use a...

Many a Turkish made pcp can be rather picky on slugs as far as size. In 25cal sorry to say there´s rather few flavors to pick from, but start by pushing one of them 33,95´s through the bore with the barrel off the gun and then take a micrometer to it to get an idea of your bore measurements...

Many many moons ago now i picked up a 22cal Kral Puncher Auto. All was well, for a brief while. It was accurate enough, not an issue, but far from reliable. It would, to the letter, hammer the stock mag innards out of shape was anything changed from the stock setup. Margin of error simply put...

Correct in that they are not. They are however under the same ownership (Turkey, of course). The original idea for the Reximex brand was to pull "upscale Kral" guns if i´ve been informed correctly. As to how they´ve succeeded, in all honesty a little to early to tell IMO. The Gunnar indeed is...

Btw Salim. While you´re in there it might be a good idea to replace the plastic material used for seal on the actual valve too. What Aselkon were thinking, no idea but.. it wears so fast it´s to laugh at. I have since turned what i need myself, and modified the poppet to run on a 2mm shank...

Hey Salim. Let´s turn the tables a bit, what seems to be the problem with your current regulator? I´m more than familiar with the Aselkon units and am here to tell that the wise men of Aselkon arrived on that a suitable material for the seal of the reg is... rubber. Morons. Anyone with witz of...

Many, while far from all, of the Turkish made guns run semi tight rifling twist, which is what slug guns thrive on. If there´s one brand that truly is garbage out of the box it´s the early Turkish made Aselkons. However. That there is an Aselkon MX-10 that got a decent sized plenum tossed...

I´d say this is a matter of balance. To my findings very much can be had by altering that power adjuster. Get or make one that in essence will close the shutter completely, and just open ever so slightly at full. Point being that such a restriction is a constant and should to greater avail hand...

@ Graycrait. The ones i´ve been into for instance have a valve out of a material that´s got to be recycled Coke cans from far east Asia. Cough at it and it´ll strip threads and what not. Barrels are decent though, but the general build, IMO, is juuuust to keep the thing together. Fact is, i´ve...

Went down that route many many moons ago. Back then the max we were dealt was the 25.4 Knockouts. Had them running just up to the wall, so it sure can be done - yes even on the stock barrel length. But truth be told, the Stormrider is a rather weak design all said and have sure moved on since...

@ Derick. What do you want to know? For the most part enlarging the so called transfer ports, which entails the exhaust port on the valve and the barrel entry too, is rather straight forward. Just use a drill bit of choice and common sense. The drill bit to rest though... follows what´s just as...

Ontopic Got one of those. The AR-6 is mentioned above, this is from before they turned Evanix. Sweet little revolver rifle, have to say. Shoots very well when i feed it pill by pill. For some reason groups opens up a tad as soon as i use the revolver mag for whatever reason. Need to look into...

22 caliber. 30 meters. Done with an unregulated Hatsan Nova. 10 shots. Opening at its largest 6,8mm. Pills, regular JSB Knockouts right out of the tin.

With the working parts of the reg out of its hole, looks deep in there with the trigger and what not removed of course. Close to the bottom of that hole there´s an o-ring, and when an Impact leaks out of the bleeder hole i´d say 9 times out of 10 it´s that o-ring that´s gone bust. As mentioned...

Give that a second thought. The Throne, both versions, sure lacks plenum volume as well Unit sports what Reximex call a "pre-chamber" stock, but that thing is like the original plenum on the Impact, along 20+cc´s and that sure won´t cope. So as you can see in the picture i enlarged that with...