Search results for query: *

Thanks! I am replacing two pistons soon and will check that O-Ring. I have a ton of O-Rings on hand.

Where is that part found?

My Uragan 2 in 22 cal was SUPER loud because it was supersonic from the factory with most lighter pellets. I tuned it down inside on the regulator (no amount of external adjustment made any difference). Now it is my most quiet and accurate air rifle, without the need for an external moderator...

Sorry, never saw the notification. I had it set on the lowest sensitivity which I assume was Sen 1, but I can't check it as it is now DOA, about one month past the warranty. I cut into it to see if I could replace the battery, but so far have not been able to find the battery in there. The PCB...

I have used both. The direct powered one was wired into the pump motor connector so it only ran when the pump was running. It is still working after almost 3 years. Coincidentally my sealed battery vibration activated one was found dead yesterday at 2 years and 1 month past the purchase date...

I have been filling two 30 minute and three 45 min SCBA tanks all the way to 4500 psi for over a year now and my CS4 is running as well as the day I put it into service with nothing more than the required grease knob turning when the hours are reached. I have a large "orange" secondary water...

Thanks for both of the tips guys!

I was going to get rid of my 22 Jet but decided to keep it. Are there any high capacity mags made for it? My son lost one of the two mags I had for it and would prefer higher round count. Also is $15 the best price going for a factory one in 22 cal?

My mags from Carm / Darko work flawlessly. I get the right side inserting version so I can use a side focus wheel. My factory mags with the metal shim fix are also jam proof, but definitely not as smooth as the Carm mags.

My fix only solves the 2nd pellet being dragged back out of the magazine. Sorry I didn't make that more clear. I have never had any failures to feed going in, but lots of jams caused by pellets being pulled backwards.

Congrats! What scope were you using?

Maybe I should watch your video again. What I got the first time was that the round going in was jamming which is different from my problem with it pulling the 2nd pellet partially back out of the magazine when caulking it to load the next one. Do the Firewalker mags work with the polymags? I...

Yup, it is too big and causes the different jamming problem that I had with all of my factory Notos mags. Had I known they would do this I would have not purchased a dozen of them. But, once I owned them I wanted to make them work! At my hourly rate then ended up being $75 magazines. It is like...

Great video and thanks for posting it! Also excellent failure analysis figuring out the issue with the probe. I was able to get all my factory Notos magazines to work perfectly with any pellets I tried over a year ago by adding a small cover extension as shown in the photo below. Copy and...

I have replaced all my Aimpoints, EOTechs, Trijicons and whatever else on my nicer guns with Holosun micro red dots. I prefer the fully enclosed versions with a solar panel. I still use a few sub $50 red dots on super cheap airguns and 22s as it is hard to justify a $180 sight on a $90 gun. lol

Those are HEVC videos. I have never seen that type before, but if you want to view it, you will need to download an extension for most browsers.

Yikes! A good friend of mine who was an amazing gunsmith and antique firearm restorationist was permanently blinded by a similar incident but it was hot bluing salts, not molten lead. An investigation after the fact found a foreign object inside the tube magazine of the gun. IIRC He had...

You are welcome. Good luck with the deal!

Good observation. Some people feel that they simply cannot pay asking price. A long time friend of mine, when asked for a lower price on a bid he presented to a customer would often scratch out the bid price and write down a price significantly higher! One lady laughed and said, OK, good joke...

I would say yes it would be rude to ask for a lower price if they specifically state in their ad that they will not entertain lower priced offers or if the price is "firm". If there is no reference of not wanting to get lower priced offers then ask away in my opinion. Just don't offer half of...