Search results for query: *

The distance from center to top is ~15mm & bottom is roughly the same, however alignment is absolutely critical (new software has alignment detection though - so you can detect if there's an issue) I would not recommend to use the outer surfaces on the Chrony as a reference point, and only...

The only other Chronograph i've seen with repeatability accuracy is the Pro-chrono DLX, but they specify it in timing ns... kinda frustrating, you'd have to do the maths on sensor spread & calculate a %. Adapters - all the work is still valid, you'd just add a 20.1mm round end to slide into a...

Your expectation of chronograph accuracy is far too high - as is most peoples. Due to manufacturing tolerances, unless they're live shot calibrated - you're just not going to get the accuracy of the actual pellet speed. You can get 1% shot to shot consistency, but you'll see a higher variance...

Going through a rebuild & struggling too... keep blowing out the green orings. Did get a few to work ok & then it was like the check valve was stuck - looks like the other orings are done. One question... note how hill give you the brass tip & not the o-ring..... is the brass possibly wearing...

I can only talk about the regular NateChrony - some barrels it does affect POI, others not - depends on the barrel. So i'll never make the claim. There's a few pro bench shooters that use it & just leave it on their barrel 100% of the time with great success - but again, I wont claim that...

(NateChrony - NOT the BuckChrony - ref BuckRails product page for the buck chrony) Like a 457 Texan at a few hundred fpe? yeah no issues: Inner is ~16mm, good for 50cal up to ~150-200fpe Carbon version on the way for the big power (which is what Papa used above) Slugs are actually much...

There are the variable adapters which allow it to be used over un-threaded barrels or moderators up to 55mm (i.e. Donny Sumo)

Doesnt that hang on the end of the barrel?

yeah 100% understand It also cannot be used with powder burners & isnt good with CO2, muzzle mount isnt a magical solution for everything & there's reasons to purchase different units for sure.

Yeah this was a design decision. I can add a screen to the Chrony, it'd be small, fragile, hard to read, add weight on the muzzle, add cost, maybe a hinge for it to fold out & face rearward (fragile!), if there's a problem you'd HAVE to come to me for a replacement. IMO a bad solution these...

Sorry if it sounded aggressive - not my intention. My point was also that "free shipping" is never actually free, robbing peter to pay paul as it were

Sorry - maybe I didnt put it well. There's 2 things with Chronograph accuracy: - How close the result is to the actual speed of the pellet - How consistent the results are at a given speed (cant think of a better word when talking uncertainty) Example: - Pellet speeds: 1000, 998, 999, 1002...

Dont disagree at all. If you're a casual shooter - you probably dont need this at all. The only other use case for non-benchers/serious would be equipment tuning & diagnosing - how consistent is your platform & can you get any more out of it. If 10fps variance is enough - then 100% that'll do...

Most bench shooters demand the best accuracy on the market & well below that... however its mostly around shot to shot consistency, which is typically better than the absolute measurement of speed.

Holler if you need anything... Yes - its a little more technie than the traditional shoot over chrony's, this is by design. We didnt include a battery or a screen - as "everyone" has a mobile - which is the worlds best screen & has a battery. This allows us to make it more rugged & keep costs...

yeah - side note... Andy mis-spoke saying you had to calibrate it from another unit - that feature is to "un-calibrate" it so to speak. Every NateChrony is shoot-through calibrated from our certified/traceable master chronographs to within 1fps @ 1,000fps. So its the most accurate on the market.

Holler if you need anything. Shipping will never be free - as its sent from Australia, i've just changed to a much faster shipper which is cheaper too, so I might bump the price & "include free shipping". There's also Hajimoto who stocks it locally in the US

Rick - glad its running ok. Compare it to another Chronograph? The NateChrony is calibrated to our certified/traceable master chronographs & is within 1fps @ 1,000fps. If you do compare it to another chrony - check its specs! Labradar - ~10fps @ 1,000 Garmin - 8fps @ 1,000 (depending on pro or...

Who does a heap of back to back comparisons in all conditions - it'd be expensive & most YT channels are somewhat "shills" for specific brands. I've literally calibrated 1000's of chronographs & my OCD has made it an interesting adventure. Things like how its mounted or fixed, even vibrations...

Overall it appears they're well thought through - i'd have pretty high confidence in their process & methodology. Radars... there's been some really good talk on other forums from guys that have worked with radar for 40+ years, they basically giggle when radar Chrony's come up.