Search results for query: *

Then my follow up question would be. Should you really be mounting a bipod to a bottle adapter & bottle on an air gun, like the one I added to the Notos?? My new logic says no. There should be a solid frame system back to the body of the air gun. Am I goofy footed on this??

Thank you. excellent read. Hadn't found it in my searches. It would seem to make sense in that both the barrel and the bottle have some wiggle. You can never know where the best, correct position is.

I am working through some issues I am having with a Dream Valve, incurable leak thus far. But as I try to think through all the angles and possible cures, the question in the title crossed my brain. Does a bottle/barrel band potentially throw off or hold the barrel at a different position. I...

I am glad to hear it went well for you. Interesting about the plenum to gun connection. That was my first problem. It kept blowing o-rings, 3 times. Finally ended up curing it with a slightly smaller o-ring that fit into the angle better and was completely captured, now no leaks. I have admit...

Thank you. Took it apart again yesterday. With what limited measuring tools I have, it seems the inner piece that has the 8mm hex in it maybe milled slightly off. Or the outer tube might be off. The tube is 27 mm id ish. With 6 o-rings tested, the od with the o-ring mounted was 27.15 mm ish. 6...

Thank you. Have worked that direction. Can't remember my order number from December, I found there invoice and charge to my cc and passed that along, but no progress made. They seem a little hesitant. Guessing they think I bought the Alibaba version. Even though I just purchased and received...

Thanks for the replies. I think I will take it apart again and really inspect the plenum inner two seal surfaces and see if there are any flaws or cracks. If nothing, then I'll put new orings in again, and try the permatex route. Beginning to think I got a lemon of a Huben Dream Valve.

Just replaced the plenum o-rings in my Huben Dream Valve 7075. Had another problem that I posted earlier and that seems to be cured. One of the 4mm x 4mm set screws at the plenum swivel was leaking before the new internal o-rings and is still leaking after their replacement. My fingers are to...

Thank you all! Absolutey agree with everyone. The target material was 1 inch rubber mat, or stall mat at 30 yards. I can only answer the meter response capability as, I think so. They responded immediately to sounds and we had other eyes watching meters at all times. To my ears, the No Mod and...

Had the family over to do a sound test. Thought I would find the quietest of mods for my Notos. All I got was a little confused or got a little information clarified. I'll describe what we did and attach the results. Looking for input on doing a better test structure please. A gentleman was...

Hi Ed, Had a similar problem after just a couple of fills on the airgun. What worked for me was to take off the burst disc, then run the pump and poor water into the hole. It flushes out the grease from over greasing, (didn't think I had, but I did). There is a video on the tube from the seller...

Hello, Have the Dream valve and wondering if anyone else is having issues with the plenum end to air gun blowing o-rings? Mine has held great since I got it a couple months back. Went out today to squeeze off a few down range and the gun was empty. Put it on the compressor and the leak was...

Success!!! Water washing did the trick. Big bottle and Notos are back in action. Thanks to everyone for your suggestions and your time!!!!!!!!!!! A question: Would it be worthwhile to create a section with all the problems and cures for each particular air gun, compressor, etc? I did a couple...

Whale poop. Grease system checks out fine. Plenty of grease and the hole is open on the black "gasket" inside. Just cleaning out all the valves at the moment. So far, a bunch of black greasey goo around most everything. Cleaned that all up. I'll work my way from the front to the compressor...

Unfortunately, I have joined the ranks of a poorly running CS4. Got about 4 good hours out of it, now it won't go above 2350 PSI. I seems to load up and barely run the piston? in the compressor before it turns itself off. Has anyone ever gotten/found a manual for these things?

Have to admit less noise is why I moved the direction of PCP's. Have many louder guns, just don't like the noise. I would play with the moderator if I could get the Notos to make no noise. From all the reading I have done so far, moderators are verrry subjective. What is quiet to me and my...

Mine seems to be pretty quiet out of the box, or it could be that I am half deaf on the right ear:LOL:. My wife says both.

Hello Rain, Hate The Rain Here in Oregon. Currently getting .46 of an inch per hour, I'll send you some:) Wondering where you located the cocking lever for your Notos if you don't mind sharing? Thanks

Thank you all for taking the time to give an excellent explaination. I was missing the max fill pressure angle of the unregulated versus the "static" hammer set point of the regulated air gun. I have ghosted many forums on as I have attempted to learn things throughout the years. This is...