Skout .25 Skout Epoch

Jump to latest Follow Reply
Man id like some trigger time on one of these scouts, but i dont think any Dane have one.

I have not dared to look at the barrel of my Two, that is what is inside the tensioning system, CUZ i would then need a torque wrench to put it back together to be sure where i am with the tensioning of the barrel.

I assume i could just go and look at a pic at Lother Waters home page, to get looks and specs / measurements.

Later in the year, probably get torque wrench and a few other knick knacks.
 
Upvote 0
Centercut said:
So I get home after post #357, and my new 25mm digital gauges were in the mail. The ones on there are good, but 28mm and stick out too far.
After depressurizing the breech block, I replaced both bottle and HP plenum pressure gauges. I left the LP gauge factory.
When I pressurized the block - surprise - the HP reg leaked through the middle as it has done about 3 or 4 times in the past. It hasn’t done that in quite a while since I replaced the Polyurethane orings with BunaN, but leaky is back. Hard to be disappointed the way it’s shooting in .30 caliber. Might have done well at the NAC, but that’s kinda far from San Diego. 😉
Click to expand...
Is it the kind of leak that a few twists of the HPR stops it??
Did the leak stop when you replaced 9009 ?
..I have a feeling the problem is o-ring 9006, but seems impossible to replace.
 
  • Like
Reactions: Centercut
Upvote 0
Centercut said:
So I get home after post #357, and my new 25mm digital gauges were in the mail. The ones on there are good, but 28mm and stick out too far.
After depressurizing the breech block, I replaced both bottle and HP plenum pressure gauges. I left the LP gauge factory.
When I pressurized the block - surprise - the HP reg leaked through the middle as it has done about 3 or 4 times in the past. It hasn’t done that in quite a while since I replaced the Polyurethane orings with BunaN, but leaky is back. Hard to be disappointed the way it’s shooting in .30 caliber. Might have done well at the NAC, but that’s kinda far from San Diego. 😉
Click to expand...
Could be the poppet seal inside the reg as mentioned above on MFE 105. You can pull out MFE107 then pressurize and if still leaking its probably from the poppet seat per SKOUT or turn it in to reseat and then reset desired pressure. You can get 9006 apart but will need some non-marring plyers and an allen key in the end. Once apart the o ring can be replaced but I believe SKOUT would just send you new poppet as well.
 
  • Like
Reactions: Centercut
Upvote 0
manabeknives said:
Is it the kind of leak that a few twists of the HPR stops it??
Did the leak stop when you replaced 9009 ?
..I have a feeling the problem is o-ring 9006, but seems impossible to replace.
Click to expand...
No. I took it apart, cleaned and regreased everything, and it’s fine now. I hope it lasts through the Oregon event. I’ll do it again before RMAC. Plus I have a spare reg both HP and LP
 
  • Like
Reactions: Revoman and manabeknives
Upvote 0
Centercut said:
You don’t need to send it in to Skout. All you do is install an FX Superior liner in the Outer housing you order from Skout. Choose your length, 700mm, 600mm, whatever. Easy day.
As far as depressurizing the gun between uses I don’t, but Augie @Bigragu does. I’m gun shy doing that since it bit me in the ass in December 2023 when I brought the gun to the Orlando EFT GP and the LP reg failed when I pressurized the gun the morning of the competition.
I’ll live with a 200 to 300 psi drop daily, not a big deal.
Click to expand...
So what barrel length are you actually using then?
 
Upvote 0
Centercut said:
Yes. It’s as accurate as they come. I shoot the AEA 45s at about 905 fps. Good enough to be competitive at the major Pro level.
Click to expand...
So I’m a little confused. Ive read that to use the fix barrels on the scout you have to send the barrel in and they have to modify it to make it work, is that true? If so what did you have to do? Also are you able to use a moderator with the setup? Thanks
 
Upvote 0
Aunsell said:
So I’m a little confused. Ive read that to use the fix barrels on the scout you have to send the barrel in and they have to modify it to make it work, is that true? If so what did you have to do? Also are you able to use a moderator with the setup? Thanks
Click to expand...
No, you buy a barrel assembly for the length and caliber of FX liner you want. They send it to you and you install the liner. Easy day. Yes, you can use the factory mod or your own with a DonnyFL adaptor.
 
Upvote 0
Centercut said:
No, you buy a barrel assembly for the length and caliber of FX liner you want. They send it to you and you install the liner. Easy day. Yes, you can use the factory mod or your own with a DonnyFL adaptor.
Click to expand...
Sorry for all the questions, I have one more. 😃, I’ve noticed in all the Skout social media posts and from their shooting at competitions from their own guys, it looks like most of their group is using external bottle regulators unless I’m looking at something incorrect. I’m wondering if they’re having the same problem you were. And instead of solving the problem. They’re just using that external regulator as a Band-Aid? Or is there a benefit by adding another regulator. What are your thoughts?
 
Last edited:
Upvote 0
Aunsell said:
Sorry for all the questions, I have one more. 😃, I’ve noticed in all the Skout social media posts and from their shooting at competitions from their own guys, it looks like most of their group is using external bottle regulators unless I’m looking at something incorrect. I’m wondering if they’re having the same problem you were. And instead of solving the problem. They’re just using that external regulator as a Band-Aid? Or is there a benefit by adding another regulator. What are your thoughts?
Click to expand...
I think the bottle reg fixed the symptoms and not the cause. Neither Augie nor me had an issue once we did our oring upgrades on the factory reg. We got the ES under 10 fps and SD under 3 fps for a 40 shot string. The in-line reg is the “easy button”. 😉
 
Upvote 0
Centercut said:
I think the bottle reg fixed the symptoms and not the cause. Neither Augie nor me had an issue once we did our oring upgrades on the factory reg. We got the ES under 10 fps and SD under 3 fps for a 40 shot string. The in-line reg is the “easy button”. 😉
Click to expand...
Well, that seems dumb, especially since even the Scout people don’t wanna fix it. So it sounds like you’re either stuck with putting the in-line regulator or doing the O-ring fix if you’re wanting this gun to shoot perfect!
Wouldn’t have a link for that O-ring you replaced would you?
 
Last edited:
Upvote 0
Aunsell said:
Well, that seems dumb, especially since even the Scout people don’t wanna fix it. So it sounds like you’re either stuck with putting the in-line regulator or doing the O-ring fix if you’re wanting this gun to shoot perfect!
Wouldn’t have a link for that O-ring you replaced would you?
Click to expand...
It’s a standard BunaN 90 duro size 009 oring. Or you could use a Viton 90 duro. The PU factory oring tends to take a “set”.
 
Upvote 0
Centercut said:
I think the bottle reg fixed the symptoms and not the cause. Neither Augie nor me had an issue once we did our oring upgrades on the factory reg. We got the ES under 10 fps and SD under 3 fps for a 40 shot string. The in-line reg is the “easy button”. 😉
Click to expand...
I’m curious what exact oring in the reg needs changing? The ES on mine is hit or miss. Some days decent and some days it totally sucks due to a few errant low velocity shots.
 
Upvote 0
Trucker3573 said:
I’m curious what exact oring in the reg needs changing? The ES on mine is hit or miss. Some days decent and some days it totally sucks due to a few errant low velocity shots.
Click to expand...
IMG_2765.jpeg
 
  • Like
Reactions: Trucker3573 and Dairyboy
Upvote 0
Centercut said:
I think the bottle reg fixed the symptoms and not the cause. Neither Augie nor me had an issue once we did our oring upgrades on the factory reg. We got the ES under 10 fps and SD under 3 fps for a 40 shot string. The in-line reg is the “easy button”. 😉
Click to expand...
My Epoch has been doing very well after i made the changes to the o-rings suggested by @Centercut
 
  • Like
Reactions: Dairyboy and Centercut
Upvote 0
This is my last session
Epoch .22 BullBarrel, JTS .22 dead center

Shot count: 81

Low: 972 FPS
Hi: 986 FPS
Avg: 981 FPS
Spread: 14 FPS
STD Dev: 2.5 FPS

29-Sep-2024 13:40:53,972,FPS,46.3,FT Lbs,
29-Sep-2024 13:42:47,975,FPS,46.6,FT Lbs,
29-Sep-2024 13:43:24,978,FPS,46.9,FT Lbs,
29-Sep-2024 13:44:08,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:44:26,980,FPS,47.1,FT Lbs,
29-Sep-2024 13:44:45,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:45:34,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:45:51,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:46:01,979,FPS,46.9,FT Lbs,
29-Sep-2024 13:46:26,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:46:48,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:47:17,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:47:36,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:47:57,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:48:19,976,FPS,46.7,FT Lbs,
29-Sep-2024 13:48:39,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:48:55,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:49:13,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:49:28,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:50:25,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:50:44,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:51:01,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:51:22,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:51:52,983,FPS,47.3,FT Lbs,
29-Sep-2024 13:52:14,984,FPS,47.5,FT Lbs,
29-Sep-2024 13:52:41,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:52:56,986,FPS,47.6,FT Lbs,
29-Sep-2024 13:53:12,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:55:14,986,FPS,47.6,FT Lbs,
29-Sep-2024 13:55:39,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:55:59,978,FPS,46.9,FT Lbs,
29-Sep-2024 13:57:27,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:58:01,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:58:31,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:58:48,979,FPS,46.9,FT Lbs,
29-Sep-2024 13:59:16,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:00:19,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:00:39,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:00:52,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:01:05,982,FPS,47.2,FT Lbs,
29-Sep-2024 14:01:32,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:01:50,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:02:22,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:02:37,980,FPS,47.1,FT Lbs,
29-Sep-2024 14:02:56,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:03:21,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:03:45,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:04:04,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:06:05,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:06:26,980,FPS,47.1,FT Lbs,
29-Sep-2024 14:06:46,980,FPS,47.0,FT Lbs,
29-Sep-2024 14:07:09,978,FPS,46.9,FT Lbs,
29-Sep-2024 14:07:27,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:07:50,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:08:15,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:08:53,981,FPS,47.1,FT Lbs,
29-Sep-2024 14:09:15,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:09:35,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:10:01,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:10:21,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:10:55,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:10,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:28,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:49,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:12:07,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:12:32,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:12:48,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:13:05,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:13:36,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:13:56,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:14:21,982,FPS,47.2,FT Lbs,
29-Sep-2024 14:14:39,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:14:53,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:15:10,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:15:24,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:15:58,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:16:14,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:16:38,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:16:57,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:17:15,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:17:27,985,FPS,47.5,FT Lbs,
 
  • Like
Reactions: Headshots, Dairyboy and Centercut
Upvote 0
manabeknives said:
This is my last session
Epoch .22 BullBarrel, JTS .22 dead center

Shot count: 81

Low: 972 FPS
Hi: 986 FPS
Avg: 981 FPS
Spread: 14 FPS
STD Dev: 2.5 FPS

29-Sep-2024 13:40:53,972,FPS,46.3,FT Lbs,
29-Sep-2024 13:42:47,975,FPS,46.6,FT Lbs,
29-Sep-2024 13:43:24,978,FPS,46.9,FT Lbs,
29-Sep-2024 13:44:08,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:44:26,980,FPS,47.1,FT Lbs,
29-Sep-2024 13:44:45,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:45:34,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:45:51,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:46:01,979,FPS,46.9,FT Lbs,
29-Sep-2024 13:46:26,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:46:48,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:47:17,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:47:36,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:47:57,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:48:19,976,FPS,46.7,FT Lbs,
29-Sep-2024 13:48:39,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:48:55,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:49:13,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:49:28,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:50:25,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:50:44,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:51:01,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:51:22,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:51:52,983,FPS,47.3,FT Lbs,
29-Sep-2024 13:52:14,984,FPS,47.5,FT Lbs,
29-Sep-2024 13:52:41,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:52:56,986,FPS,47.6,FT Lbs,
29-Sep-2024 13:53:12,983,FPS,47.4,FT Lbs,
29-Sep-2024 13:55:14,986,FPS,47.6,FT Lbs,
29-Sep-2024 13:55:39,979,FPS,47.0,FT Lbs,
29-Sep-2024 13:55:59,978,FPS,46.9,FT Lbs,
29-Sep-2024 13:57:27,977,FPS,46.8,FT Lbs,
29-Sep-2024 13:58:01,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:58:31,981,FPS,47.2,FT Lbs,
29-Sep-2024 13:58:48,979,FPS,46.9,FT Lbs,
29-Sep-2024 13:59:16,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:00:19,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:00:39,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:00:52,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:01:05,982,FPS,47.2,FT Lbs,
29-Sep-2024 14:01:32,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:01:50,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:02:22,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:02:37,980,FPS,47.1,FT Lbs,
29-Sep-2024 14:02:56,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:03:21,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:03:45,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:04:04,984,FPS,47.5,FT Lbs,
29-Sep-2024 14:06:05,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:06:26,980,FPS,47.1,FT Lbs,
29-Sep-2024 14:06:46,980,FPS,47.0,FT Lbs,
29-Sep-2024 14:07:09,978,FPS,46.9,FT Lbs,
29-Sep-2024 14:07:27,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:07:50,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:08:15,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:08:53,981,FPS,47.1,FT Lbs,
29-Sep-2024 14:09:15,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:09:35,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:10:01,979,FPS,47.0,FT Lbs,
29-Sep-2024 14:10:21,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:10:55,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:10,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:28,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:11:49,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:12:07,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:12:32,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:12:48,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:13:05,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:13:36,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:13:56,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:14:21,982,FPS,47.2,FT Lbs,
29-Sep-2024 14:14:39,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:14:53,983,FPS,47.4,FT Lbs,
29-Sep-2024 14:15:10,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:15:24,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:15:58,985,FPS,47.6,FT Lbs,
29-Sep-2024 14:16:14,981,FPS,47.2,FT Lbs,
29-Sep-2024 14:16:38,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:16:57,982,FPS,47.3,FT Lbs,
29-Sep-2024 14:17:15,983,FPS,47.3,FT Lbs,
29-Sep-2024 14:17:27,985,FPS,47.5,FT Lbs,
Click to expand...
So it’s just the one o-ring from the diagram. I ordered them …. And I don’t even have the gun yet 🤣… but I will ! 🙌
 
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu