Airforce .257 California Condor's Talon?

[jgreen]

Hello,

This is my .257 built on a TalonSS frame. I am also trying to accrue 10 posts, to you know, find the bird a new home.

 

[shambozzie]

Welcome aboard. The correct move would have been to wait for 10 useful post , then post in classifieds. Perhaps re-reading of rules should be considered. Tons of good info and folks here. Feel free to discuss your build.

 

[markhooper]

Hello,

This is my .257 built on a TalonSS frame. I am also trying to accrue 10 posts, to you know, find the bird a new home.

View attachment 475109

View attachment 475110

View attachment 475111

View attachment 475112

View attachment 475113

I like seeing open sights.. where do you get them?
been thinking about a Condor 22.. so far I only have 22.. someday maybe a big bore 30 caliber..
Mark

 

[markhooper]

Welcome aboard. The correct move would have been to wait for 10 useful post , then post in classifieds. Perhaps re-reading of rules should be considered. Tons of good info and folks here. Feel free to discuss your build.

it's good to know the rules I likely don't remember them all.. but if I am not sure, I don't .. usually I err on the thinking it's not ok when it is.. but I prefer to stay out of trouble..
I like peace and learning.. not disagreement..I like reading your posts..
do you know if there's a way to select so that people you like reading,show up? I tried clicking follow but it doesn't seem like it does anything??
thank you
Mark

 

[jgreen]

I like seeing open sights.. where do you get them?
been thinking about a Condor 22.. so far I only have 22.. someday maybe a big bore 30 caliber..
Mark

the front sight is from Amazon, yonger, the eye sight is an airforce front sight, the airforce front and rear set would be better

 

[jgreen]

Welcome aboard. The correct move would have been to wait for 10 useful post , then post in classifieds. Perhaps re-reading of rules should be considered. Tons of good info and folks here. Feel free to discuss your build.

thanks, I guess my wording wasn't clever enough

 

[jgreen]

Welcome aboard. The correct move would have been to wait for 10 useful post , then post in classifieds. Perhaps re-reading of rules should be considered. Tons of good info and folks here. Feel free to discuss your build.

it has a doug noble valve! the barrel is tj/talontunes

 

[shambozzie]

Nice looking setup. Is the bbl a tj 1-14 22"? Noted the cf tank meaning you need 3400/3600 with short bbl along Doug's 115 gn hammer and spring. Fpe @ 125/135 with 65/70 gn slug. Nice

 

[jgreen]

thank you, it is 24", 1/14 got some TSX ballistic tip copper bullets for it, the problem is i dont live where I can put it through its paces, but i think it can do 1000 yards

 

[jgreen]

Nice looking setup. Is the bbl a tj 1-14 22"? Noted the cf tank meaning you need 3400/3600 with short bbl along Doug's 115 gn hammer and spring. Fpe @ 125/135 with 65/70 gn slug. Nice

i replied above, also to get the slug out i use two striker weights with Doug's spring and Talontunes breech

 

[jgreen]

i encourage people to see the garandthumb video where they test subsonic copper in 8.6

 

[shambozzie]

What fill pressure?

 

[jgreen]

I have it filled to 4000, but have discharged at 3200 and the flat nose hunter supply slug split lengthwise and rotated in my test medium (old book) so it would likely blow a head off.

 

[jgreen]

What fill pressure?

sorry see above, still getting used to blogging, it is stored at 4000 psi