30-Yard Challenge

Went out early this morning. Got to the bench at 8am.

Wind was light at about 1-2/3 mph. One near flag deployed.

I started at 40Y with the RAW TM1000x .177 shooting FX 13.4g from 802-812 fps range. First card was an awful 185 and the second was a 190 something. Both were DQ’d because of fliers due to me not seating pellet correctly.

Joe C - chime in here. What I have finally discovered is that I ‘must’ fully press with my thumb, the pellet anll the way into chamber. I have noticed occasionally I have a bit of a hard time cocking all the way, if pellet is not 100% flush inside thimble. The TM1000x pellet probe is very sensitive and now I know that I was blaming some bad pellets because I wasn’t seating pellets completely flush with thimble.

I tested this many times today. Every single time my cocking cycle was not completely smooth, the pellet probe would force the pellet further into the chamber. It may need adjustment also, not sure.

When I finally figured this out, my accuracy improved.

One Leaderboard entry for May:
Taipan Vet 2
199-17X 30 Y Masters
JSB 20.83 Light ( First time I tried this pellet and had to turn down the Speed Dialer to get it flying at 905-910 FPS ) Both the JTS 22.07g and JSB 20.83g shoot great. Same with the AEA 21.9g.

Next up, Taipan Vet2 .22 cal 700mm barrel. Shot a few 30Y Masters, but nothing for the leaderboard in May. A couple 195’s, but I previously shot a 197 already in a prior session.

IMG_3102.jpeg


IMG_3104.jpeg


IMG_3103.jpeg


One note: My Great White 9L fill tank needs a 5-year certification and the turnaround is slow because this is the start of scuba dive season. I may be out of action until I get this completed. Might be a few weeks.
 
Last edited:
Got the Revere back from AoA.

Wanted to get an o-ring total reseal. Thank you Shane!

Set up at 12:30 today for 30y challenge targets. Wind was blowing, one flag.

Daystate Revere .22
Ammo: JSB 18.1 and 15.89
Scope: Athlon Midas Tac 6x24x50
Wind: crappy
Distance: 30 Y

Leaderboard submission:

194-9x

Not my best, but the wind was tough.

View attachment 554459

View attachment 554460
just to get this straight , when your shooting the target is always hung vertical , correct ? because i see some bench targets hung horizontal, in use . which to me when i look at your targets the wind drift is off .
 
just to get this straight , when your shooting the target is always hung vertical , correct ? because i see some bench targets hung horizontal, in use . which to me when i look at your targets the wind drift is off .

Not following…

I do always shoot vertical ( portrait vs. landscape) hung targets. I suppose I could try hanging them horizontally.
What does shooting vertically vs. horizontally have to do with windrift? Can you clarify?
 
Went out early this morning. Got to the bench at 8am.

Wind was light at about 1-2/3 mph. One near flag deployed.

I started at 40Y with the RAW TM1000x .177 shooting FX 13.4g from 802-812 fps range. First card was an awful 185 and the second was a 190 something. Both were DQ’d because of fliers due to me not seating pellet correctly.

Joe C - chime in here. What I have finally discovered is that I ‘must’ fully press with my thumb, the pellet anll the way into chamber. I have noticed occasionally I have a bit of a hard time cocking all the way, if pellet is not 100% flush inside thimble. The TM1000x pellet probe is very sensitive and now I know that I was blaming some bad pellets because I wasn’t seating pellets completely flush with thimble.

I tested this many times today. Every single time my cocking cycle was not completely smooth, the pellet probe would force the pellet further into the chamber. It may need adjustment also, not sure.

When I finally figured this out, my accuracy improved.

One Leaderboard entry for May:
Taipan Vet 2
199-17X 30 Y Masters

Next up, Taipan Vet2 .22 cal 700mm barrel. Shot a few 30Y Masters, but nothing for the leaderboard in May. A couple 195’s, but I previously shot a 197 already in a prior session.

View attachment 557693

View attachment 557694

View attachment 557695

One note: My Great White 9L fill tank needs a 5-year certification and the turnaround is slow because this is the start of scuba dive season. I may be out of action until I get this completed. Might be a few weeks.
Tommy, I suggest you check with your local or a neighboring fire department to find out who they use for their tank hydrotesting. Also, check for any fire extinguisher sales/service businesses in your area as many of those provide hydrotesting services.
Marvin
 
Tommy, I suggest you check with your local or a neighboring fire department to find out who they use for their tank hydrotesting. Also, check for any fire extinguisher sales/service businesses in your area as many of those provide hydrotesting services.
Marvin

Thank you Marvin.

My local Dive Shop recommended a very reputable SCBA and Scuba Certification Shop. They charge $72 and thoroughly inspect the tanks. Py Barker in Raleigh is doing my hydro test. I spoke to the owner and he can/will do my 4500 psi Great White.

Ironically, my 5-year cert was due December 2024. My Dive Shop caught it recently in filling my tank and told me they can’t fill it until I get it certified. NP, you don’t mess around with HPA, so I’m glad for the reminder.
 
Tommy, I seat mine flush with thimble as well my probe is set pretty tight against thimble (delrin seat) Mine is tight enough that over time it’s actually deformed this seat? But that’s how I received it, you can back the the probe out a little or make it tighter if wanted. It’s simple enough to do. I believe if you have a lathe or know someone who does you could make a longer pin in front of delrin seat but don’t know if it would really make a difference? Also pellets with a deeper or shallower internal skirt pocket will have a different effect on seating depth, I used to think this really mattered?
 
Not following…

I do always shoot vertical ( portrait vs. landscape) hung targets. I suppose I could try hanging them horizontally.
What does shooting vertically vs. horizontally have to do with windrift? Can you clarify?
If you hang the target portrait the wind is say east then pellets can move to the right of POA if the target is hung landscape then the drift looks up when posted here as portrait . A lot of bench rest shooters hang landscape so they don't have to adj. vertical as often for practice .
 
If you hang the target portrait the wind is say east then pellets can move to the right of POA if the target is hung landscape then the drift looks up when posted here as portrait . A lot of bench rest shooters hang landscape so they don't have to adj. vertical as often for practice .

Very interesting.

Stan, I kind of see the point. Using horizontal or landscape means fewer vertical adjustments. Thanks for the tip,
 
Went out early this morning. Got to the bench at 8am.

Wind was light at about 1-2/3 mph. One near flag deployed.

I started at 40Y with the RAW TM1000x .177 shooting FX 13.4g from 802-812 fps range. First card was an awful 185 and the second was a 190 something. Both were DQ’d because of fliers due to me not seating pellet correctly.

Joe C - chime in here. What I have finally discovered is that I ‘must’ fully press with my thumb, the pellet anll the way into chamber. I have noticed occasionally I have a bit of a hard time cocking all the way, if pellet is not 100% flush inside thimble. The TM1000x pellet probe is very sensitive and now I know that I was blaming some bad pellets because I wasn’t seating pellets completely flush with thimble.

I tested this many times today. Every single time my cocking cycle was not completely smooth, the pellet probe would force the pellet further into the chamber. It may need adjustment also, not sure.

When I finally figured this out, my accuracy improved.

One Leaderboard entry for May:
Taipan Vet 2
199-17X 30 Y Masters
JSB 20.83 Light ( First time I tried this pellet and had to turn down the Speed Dialer to get it flying at 905-910 FPS ) Both the JTS 22.07g and JSB 20.83g shoot great. Same with the AEA 21.9g.

Next up, Taipan Vet2 .22 cal 700mm barrel. Shot a few 30Y Masters, but nothing for the leaderboard in May. A couple 195’s, but I previously shot a 197 already in a prior session.

View attachment 557693

View attachment 557694

View attachment 557695

One note: My Great White 9L fill tank needs a 5-year certification and the turnaround is slow because this is the start of scuba dive season. I may be out of action until I get this completed. Might be a few weeks.

Nice shooting to you Tommy and the rest of you boys - some great scores being submitted.

@Tommy - did you shoot the 199 17X with the .177;TM1000 or the .22 Taipan? The card says the TM1000 but you writeup says the Taipan…
 
Thanks NA, I really haven’t done any tuning to the gun they come pretty set from Martin. It shoots the original 13.4 jsb’s at around 815fps, I put an air stripper on it “barrel likes it better than a moderator!” I have a Athlon 15-60x56 Ares ETR scope on it, it’s ok! But better choices out there for just a little more$$ “think sightron”.
I do want to say that at 40yds with a .177 much wind especially a switching or variable speed wind your already behind the Eight ball! That’s why I normally post what my flags are doing because people can understand why I might shoot a score like tonight, mind you this might be the best 40yrd card I ever shoot with this gun and barrel!.

Thanks for providing the details Joe. QUESTION: What magnification did you have the Ares set to when you shot the card?

Great card - 196 13X 40-Masters with a .177 is awesome shooting!

-Ed
 
30 Yard Masters submission: 200 18X

FX Panthera 700mm, one 18 round magazine, 🇵🇭 JMS-Pro 18.3gr, Vector Optics Sentinel X @20X mag, Accu-TAC FC-4 G2 Arca Spec bipod and Protektor rabbit ear rear bag.

Weather app is BS 👎 Wind gusts was only around 9mph

View attachment 557606View attachment 557607

Awesome job Ricky! A 200 18X 30-Masters while timing it for speed…. I‘ve never shot 18X…. period, lol.