AEA HP SS PLUS

[Daygo619]

The bolts on these rifles are a bit small IMO. My Terminator cocks easier than my HP Carbine. I have arthritis in my right hand. Fishing thumb is what my doctor called it so I turned a larger handle for me. I find it much easier if you can get two fingers on the bolt.

View attachment 325884

On the left is original from an AEA carbine. The right is the one I currently use. Makes life much easier.

View attachment 324981

View attachment 324982

My arthritis could use a couple of these! Trying to msg u

 

[RAMJET66]

50mm long cocking knob knurled

50mm long cocking knob knurled fits anything with 6mm x 1.00 threads

bisonairriflesandparts.com

AEA hp ss 30+ and challenger cocking knob

AEA hp ss 30+ and challenger cocking knob this knob is threaded for m6 x 1.0 threads it can fit on anything with m6 x 1.0 threads this knob can be used on a bolt action but was made for the semi auto guns i have changed the design on the semi auto bolt knob to have 4 knurled lines with 3 groves...

bisonairriflesandparts.com

I had these on my Challenger SL 357 and HP SS 30+ ... very nice and very much bling bling as well. You would have to double check if it fits other models, but I think they're all the same.

the longer extended one( can be seen after opening link to Bison air) would help my HPSS PLUS 22 Cal, i can not cock it =arthritis, i did purch one from a member here , but i could not get the oem one off, so i installed it on the 1st gen hpss & it works great.

​

 

[JeffreyP123]

thanx on the CTS -V , & i can not cock the 2nd gen (artrhitis) i have been looking for a longer cocking knob, have not found one yet.

I have longer cocking knobs. Hit me up

 

[Daygo619]

Just installed @Sicumj longer knob on my HP + and makes it so much easier

 

[Perle]

Just installed @Sicumj longer knob on my HP + and makes it so much easier View attachment 331378

M

Sweet. Jim hooked me up as well

He makes some nice stuff !

What’s the Diameter on that one ??

 

[Daygo619]

M

Sweet. Jim hooked me up as well

He makes some nice stuff !

What’s the Diameter on that one ??

1/2” wide x 1” long

 

[One-Man_Riot]

BinTac has a video showing how to properly pull the bolt back: Stock braced against shoulder, pull back until the tension increases, then thumb at the back of the bolt housing to pull it the rest of the way. I was surprised at how much leverage this gave me and made cocking much easier.

 

[Dogowsky]

I'm saving up for a semi auto from them now. Can't wait to get mine!

 

[Jimborg]

Is there any trick on getting the original cocking handle off, I don't want to mar it up just incase I want to put it back.

 

[silvershooter589]

Is there any trick on getting the original cocking handle off, I don't want to mar it up just incase I want to put it back.

Counter-clockwise

 

[Sicumj]

Use a leather glove and vise grips. If it is still stuck try heating with a hair dryer.

 

[Daygo619]

Is there any trick on getting the original cocking handle off, I don't want to mar it up just incase I want to put it back

My HP plus original handle was plastic on the outside so don’t use a lighter open flame to heat up thread lock if u have this style handle.

 

[Jimborg]

I tried the leather and vise grips but it's on there good and I'm even starting to mar it some.

 

[Daygo619]

I tried the leather and vise grips but it's on there good and I'm even starting to mar it some.

U gotta get the thread lock hot. Just purchased my plus from Pellet shop 2 weeks ago. The thread for the bolt handle had a ton of thread lock on it. Try blow dryer or heat up just the metal part with soldering iron.

 

[Daygo619]

Me too ! Good looking, practical bolt handle

Everyone’s AEA s looking good !

View attachment 322831

Where can I get that rail for the bottle?

 

[Jimborg]

I heated it up a little bit with the thing I light the grill up with and I got it off!

 

[Perle]

Where can I get that rail for the bottle?

Where can I get that rail for the bottle?

I got this prototype from an eBay 3 d printer

52 mm tri rail sleeve. Check it out.

 

[Daygo619]

I got this prototype from an eBay 3 d printer

52 mm tri rail sleeve. Check it out.

View attachment 332557

Really nice! Still hunting for something like that on eBay .

 

[Perle]

Really nice! Still hunting for something like that on eBay .

What model HP do you have ?

 

[Daygo619]

What model HP do you have ?

HP SS plus .25