Anyone heard of Pneuwa Cattleman Airguns?

[knifemaker]

Reading the post on the test gun the fellow was to review. I really didn't see much wrong with the stock. Looked like nice walnut to me. Needs some oil rubbed in. 



The missing grub screw at the back of the action. The poster didn't notice that it was not threaded. Why? Because it is not for a set screw. Some people like to put a pin at the back of the scope ring to prevent walking. Not really need for a pcp, but none the less, it is there if you wish to use it in such a way. It is not a screw hole, other wise it would be threaded.
Knife

 

[knifemaker]

After have a bit of time to think about what said poster put up here. I have concerns.



Sir, if you are reading this, I see a trend here. Yet another want to be youtuber wanting a free gun to get started. However, there is an issue here. A huge one!



One, having owned an archery/gun shop for years, it is common knowledge that oil finished stocks often receive rub marks when being shipped. It in not uncommon to have to lightly rub them down with a light oil before putting on the shelf to sell. 

Further, yes the FX small gauges are notorious for being in accurate. ALL Small gauges are notoriously inaccurate. Oddly, I've not seen that much about it when attached to an FX product but keep seeing the same comment parroted here on these guns. Yes it is mentioned, but maliciously. I would have though being a want to be reviewer, you wound already have this common knowledge. 

Further, you did not know so much as to what a anti recoil walk pin hole was. 

Seems you don't know enough of the simple basics to be reviewing Air Guns at all. 

And these are the simple things. Now for the real issues. 



You have already ousted part of a private conversation. This is completely unethical. It simply isn't done and shows a complete lack of character. 

Further you offered to send a copy of the entire private message to anyone who doubted you. This is not only unethical, but is illegal in many States. If you pulled that on me, in a manner to discredit or malign in any way, I would sue the Hell out of you.

You strike me as either very young and naive, or completely unaware of your actions and the position you put your self in and the reflection on you character, or lack there of. 



I would strongly urge any member here to refrain from engaging in any pm's with you that could in any way be used to damage them. You Sir, cannot be trusted with privacy.

A basic American right protected by the U.S. Constitution. Which you have walked all over for your own purposes. 

Knife

 

[Phillk83]

Ok so first the spots are what was left behind like I said from a white grease crust from manufacturing (assuming dried silicone or something similar) that actually ate away the finish if you had it in your hand you would see it very clearly. Second the hole was threaded... and as for the guage a crack and scratched to hell is ok fresh out of the box? Forget it’s an fx guage...there’s is nothing damning I have in text message that would smear anyone or be “illegal” I was merely stating that I kept all info for my own proof and protection. As for being “new” to YouTube yes... to airguns HELL NO!! I grew up with an airgun in my hand and I’m almost 40 sir. I have a closet full that I maintain all by my self. Still have the first! Good old pumpmaster 760. I have great respect for you sir and have read many of your post over the years. But to blast someone because you didn’t like what I had to say? Attack my character? You don’t even know me! The whole point of my post was obviously missed or ignored. The quality of the rifle coming out of the box!! So distract from the point and attack me instead. Fine. Shows your true colors too sir. Have a great day. Thank you for your service! 

 

[Phillk83]

.

 

[knifemaker]

Telling the truth of what you found is not the issue. It is outing private conversation with the owner on an open forum. It is not done! Particularly in the tone you presented it in. Most forums would have already put you on a time out with a warning. Keep private, private. Period unless given permission from the other party to divulge private conversations. 

That is universal everywhere!

Apparently you missed everything said pertaining to the real issue. 

Knife

 

[Micro]

Can we stick to the reviewing and stop trying to "railroad" this guy for posting helpful information by making false accusations to try and draw attention from the mods; and just for the record, this thread is full of inappropriate posts - just a few examples - there's more...

As far as all this My pecker is bigger than your pecker, I don't care what size your pecker is. And at my age, I don't care what size mine is either. So forget even starting it with me. I don't' give a poop!



Knife



I have now has several conversations With Miss Victoria. she is first and foremost interested in any changes needed to make the guns perform above the asking price range and has ask for my suggestions as how to get there. I will be conferring with a well known to air gunners tuner who is a mechanical engineer and well known tuner. We go back many years across several forums He wishes to remain anonymous for a while yet, and after all the bashing, I don't blame hi.

 

[NemudusM]

I received mine today, I do not know how this rifle will perform but I would like to see great accuracy and shot counts, like about fifty will do and make me happy ( power isn't what I'm after ) I spent 578$ for it, so I'm hoping this is like an AA510S for half the price .

There's too much negativity here, I came looking for and idea of what to look for or what to do for the initial setup on my new Rifle, but I find people being attack for their opinions on the Customer service they have experienced. 

AncientSword you are the only one who was polite and passive-aggressive at the end. Why is sharing a positive experience Marketing? Even if the gun is trash.