N/A Broken transfer port and how to fix it

Jump to latest Follow Reply
https://www.airgunnation.com/threads/seneca-aspen-nova-freedom-parts-list.516634/
thumbnail_IMG_4421.jpg
 
Last edited:
Upvote 0
Upvote 0
marflow 777 said:
https://www.ebay.com/itm/266087400961?chn=ps&var=565938868127&_trkparms=ispr=1&amdata=enc:1XOjRCAlnTvWhcLi52-NYzQ19&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&mkscid=101&itemid=565938868127_266087400961&targetid=2320093655185&device=c&mktype=pla&googleloc=9033254&poi=&campaignid=21222258394&mkgroupid=164713660992&rlsatarget=pla-2320093655185&abcId=9408285&merchantid=118868807&gad_source=1&gclid=EAIaIQobChMIxsLQvoabhwMV8SStBh1q8RtKEAQYBCABEgK4GfD_BwE

https://vxb.com/products/m4-x-12mm-...MIvLfKgIebhwMVsB2tBh3TcQziEAQYBiABEgIsLPD_BwE


https://www.ebay.com/sch/i.html?_from=R40&_nkw=aluminum+stereo+knobs&_sacat=0&_sop=15

https://www.ebay.com/sch/i.html?_fr...83900&_odkw=round++pins&_osacat=12576&_sop=15

just some ideas for material options, you have to make it pretty LOL
Click to expand...
Nice ideas.

I have the same schematic, but obviously not parts are available.

After making the bolt shorter I don't mind the look.
But, I could probably use a black screw with a flatter head.
 
Upvote 0
markhooper said:
I honestly don't think thermoplastics will hold.. but it's worth a try.. my first thought was that brass would be easy to work but I'm thinking too much of it is drilled out with the transfer port.. so probably tool steel..I'm curious, so I am going to get mine out and see if it is steel or aluminum.. because a lot of parts are aluminum for lightweight.
let me know what you find out and if you will need one made..I really hope you can locate parts but I'll make one if you can't.
Mark
Click to expand...
If the remaining part is not magnetic, it is either aluminum or pop metal. I agree it should be simple to make, especially if you have a lathe. If you have both pieces, let me know and I will give it a try, I have a small Mill and a couple of Lathes... Mark Emmert
 
Upvote 0
MarkWE said:
If the remaining part is not magnetic, it is either aluminum or pop metal. I agree it should be simple to make, especially if you have a lathe. If you have both pieces, let me know and I will give it a try, I have a small Mill and a couple of Lathes... Mark Emmert
Click to expand...
Thanks for the offer but I have already sold the rifle.
 
Upvote 0
DO NOT SPAM THE SAME QUESTION OVER MULTIPLE THREADS
Slightly unrelated question, but I just rebuilt my aspen .25, replaced almost every single oring/seal. 80% sure i assembled everything correctly per the assembly guide, however when I try to fill up the gun with the fill probe from an air tank, the air comes straight out the barrel end and the aspens pressure guage does not budge at all. I have rebuilt the rifle a few tile in the past and never had this issue.

Any feedback or suggestions would be much apreciated.
 
Upvote 0
DesertSilver said:
Your poppet is leaking. The poppet sealing surface is very soft and will eventually wear down until it bottoms on the metal can that surrounds it. There are no stock replacement poppets available. I just cut the metal can back so it could seal again but obviously there's only so many times that can be done.
Click to expand...
You may be right.
But I sold the airgun already to someone who fixed it (I hope).
I understand that the Avenger poppets work in the Nova Liberty.
 
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu