double oh my. I'm up to 100 strokes pump said 2000 psi gun says 1400 and the pumps are getting tough. No honey I'm working out with my new pumpmaster work out equipment. I'm doing this for you.
Upvote 0
I’m surprised that much variance in pressure readings, I haven’t ran into that issue yet. I guess to be on the safe side, go with the higher pressure reading.double oh my. I'm up to 100 strokes pump said 2000 psi gun says 1400 and the pumps are getting tough. No honey I'm working out with my new pumpmaster work out equipment. I'm doing this for you.
Instead of rc car bearing i had rc car bushing, they normally get upgraded to bearings in wheels.I had same issue with bearing mod. What did you grind down to make it work? The bearing itself, or the pawl it rides on? Keep in mind I’m about as mechanically inclined as a water buffalo.
Back off hammer spring. Sounds like adj is near max, should help cocking and loudness. 4-5 turns counter clockwise.Initial thoughts.
1. This is every bit as loud as unsilenced .22 lr (standard velocity). I don't understand why it has this loud of a report.
2. Had a couple of times that I loaded and did not get a full cock/engagment so had to pull mag out to recock. That's a learning thing.
3. Mounted Japan 2-7X32 and front green fiber is way up in sight view almost at cross hair. and if I zoom in all it does is blurry the green and put it right in the middle of target sure I can see but there's a green haze.
4. The good walked the scope sighting in and hit the target at 15 yards off monopod easy peasy.
5. Of course no recoil.
I assume that is the allen head on top breach end toward stock. I moved it 4 X 1/4 turns counter clockwise.Back off hammer spring. Sounds like adj is near max, should help cocking and loudness. 4-5 turns counter clockwise.
I could download the STL files one by one.Thank you.
I can still only see one STL file.
Look on Aliexpress for "fuel filter" or "solvent traps".25 ish shots and 50 pumps later catch my breath. The 25 shots go fast. But the pumping will be an ammo saver in the long run. Two full turns of allen and have not had the bolt not engaging maybe one more for good measure.
And 25 more shots and well it's time to pump again. Darn it. On the good side I was getting tennis elbow from the springer cocking so now I'm just getting ripped core muscles (ok more like bruises on my stomach).
Does anyone make an aluminum moderator. Interesting that I can't find any such device at large air gun online stores.
Ah! Thank you, I realized after I posted that asking if you had ground bearing down was a stupid question - that would be nigh impossible. My mouth outruns my brain pretty frequently.Instead of rc car bearing i had rc car bushing, they normally get upgraded to bearings in wheels.
here it is fully assembled next to a sumo, took a vice to get the thread caps on so I'll never be able to open it back up. wrapped baffles with some 0000 steel wool cuz why not.Try downloading individually?
When my ICON showed up it was maxed out for power. With 10.6grn pellets it wasa shooting 1040's and crazy loud. I tuned the adjuster WAY down and settled at 750, much better on the noise level and 70+ shots on a fill. I still added a Buck Rail moderator for a whisper quiet experience.Initial thoughts.
1. This is every bit as loud as unsilenced .22 lr (standard velocity). I don't understand why it has this loud of a report.
2. Had a couple of times that I loaded and did not get a full cock/engagment so had to pull mag out to recock. That's a learning thing.
3. Mounted Japan 2-7X32 and front green fiber is way up in sight view almost at cross hair.
4. The good walked the scope sighting in and hit the target at 15 yards off monopod easy peasy.
5. Of course no recoil.
Does anyone make an aluminum moderator.
Yes, but not fully lined up as it was taken from another moderator. You could drill them out if you wanted.I could download the STL files one by one.
Am I seeing right, that the endcap has holes to allow the air to vent?