Daisy 747
- Thread starter arnie19
- Start date
I have not used this one but the mount I had before fit both my 46m and 777 so guessing this would be the same.
http://sunopticsusa.com/airgun-scope-mounts-izh-46-mount-sm7900/
http://sunopticsusa.com/airgun-scope-mounts-izh-46-mount-sm7900/
Upvote 0
I don't know who made this but it was on a used Daisy 777 I bought that now resides on my IZH46M.
Upvote 0
I don't know who made this but it was on a used Daisy 777 I bought that now resides on my IZH46M.
That was my old one I was mentioning above. Nice part, no idea who made it.
Upvote 0
I have successfully used 22 quick peep see through rings with makeshift shims using small PVC tubing cut in half length wise to grip-shim the barrel similar to like the Leupold rings on a Daisy 717.
Natchez Or Midway or your local sporting goods store or gun shop may be cheaper. Don't buy this one from Amazon they're most expensive for these $10 rings. Picture for illustration purposes only.
Another interesting PICATINNY option that may work for Daisy 7x7 sidelever pistols and IZH46M below. Use small PVC cut in half length wise to shim barrel to clamp them.
Natchez Or Midway or your local sporting goods store or gun shop may be cheaper. Don't buy this one from Amazon they're most expensive for these $10 rings. Picture for illustration purposes only.
Another interesting PICATINNY option that may work for Daisy 7x7 sidelever pistols and IZH46M below. Use small PVC cut in half length wise to shim barrel to clamp them.
Upvote 0
Check this out!
Maybe remove one of the screws tighten to clamp (file or shim to press fit) onto your receiver to grip using one bolt?
Probably work for other non scopeable guns? That's already a 1 inch tube too.
Maybe remove one of the screws tighten to clamp (file or shim to press fit) onto your receiver to grip using one bolt?
Probably work for other non scopeable guns? That's already a 1 inch tube too.
Upvote 0
You could drill couple holes through both sides across through the main 1 inch body and use Threaded nuts and bolts with washers to tension clamp together and remove the 2 bottom original clamping screws and the sliding it right onto the barrel or receiver. Kinda Funky looking but may just work and cheap.
Upvote 0
Looks like I have a few options .The barrel is only .441 in diameter and is very close to the tube that the pump rides in so surrounding the barrel is out but a clamp on will work . Thanks for the information
Upvote 0
The sun optics one works great on the Daisy 7 series/717-747-777. I have them on my 747 and 777.
Upvote 0
Late to the party, again, but I'll cast a second (or third?) vote for the Sunoptics. It is what I have on my two 747's.
Upvote 0
Upvote 0
Good afternoon, I needed help in relation to the handle of the Daisy 747, I recently bought one and it comes with the plastic ones it comes with, could you help me tell me where you bought them and if possible, do they make them or are they left-handed?
Upvote 0
Good afternoon, I needed help in relation to the handle of the Daisy 747, I recently bought one and it comes with the plastic ones it comes with, could you help me tell me where you bought them and if possible, do they make them or are they left-handed?
Upvote 0
Daisy used to sell the plastic grips in left handed. The guns were all sold with right hand grips, so you had to call Daisy to get the left handed ones for a decent price.
Don’t know if they still sell the left grips now that they have discontinued the pistol.
Worst case, get a couple blocks of wood and carve away anything that doesn’t look like a grip…
Good luck, hope you are able to find some grips.
Don’t know if they still sell the left grips now that they have discontinued the pistol.
Worst case, get a couple blocks of wood and carve away anything that doesn’t look like a grip…
Good luck, hope you are able to find some grips.
Upvote 0