You just shoot the rifle until it is below 80 and measure fps. Then you fill up to 90 and measure fps, etc. just one degassing.
Upvote 0
Daystate Huntsman .22 Regulator pressure
- Thread starter EPG
- Start date
It was the huma with the extra plenum. I feel like the piston wasn't sealing since all the outside orings were perfect and I even added floss under them to make them fit tighter. Same leak before and after. Pulled the reg and went back to stock. Got tired of handpumping and at the unregged state can shoot from 200 bar down to 175 bar with plenty of shots and stay in a tight arch.
Upvote 0
With my .22 maverick I'm shooting 18g pellets at 890 fps with 85 bar on the second reg. I wonder if its because of the plenum size ?
Really like the Daystate huntsman line.
Upvote 0
Among the rifles I own there is a Daystate Huntsman in .22 Cal, so yes, I am able to notice the differences.
Last edited:
Upvote 0
What I have noticed is that a rifle that was not designed to use a regulator need more preassure to work properly and if you install on it a regulator then the rifle is not so effective. Normally they loose power with the regulator.So not much gain.
Upvote 0
I have a factory Huma regulated, Huntsman XL in .22 cal. Reg pressure on it is set at 150 bar. Not sure if transfer port size is equal on your gun, but mine shoots JSB 18 gr. around 848 fps as I recall.
Upvote 0
Excellent info - thanks, I appreciate.
I’m thinking that I will try 150 bar as my initial reg pressure..
-Ed
Upvote 0
This thread will help me.
If it’s not known, the Brocock Concept Lite uses the same regulator as the Huntsman.
If it’s not known, the Brocock Concept Lite uses the same regulator as the Huntsman.
Upvote 0
I think my .22 cal Revere Regulator was set by Daystate at 165-170 BAR. That did seem high to me, but it’s what the Manufacturer recommended.
250 BAR fill to 170 BAR yields about 36 shots approximately.
250 BAR fill to 170 BAR yields about 36 shots approximately.
Last edited:
Upvote 0
@tommyb
I'm not the best guy to give tuning advice.
But if I may suggest, add these details to your post and the cognoscenti will have the info needed to respond
- FPS across at least 10shots (better all the way until it falls off the reg)
- Pellets or slugs
- Ammo weight
Just my too sents
Edward
I'm not the best guy to give tuning advice.
But if I may suggest, add these details to your post and the cognoscenti will have the info needed to respond
- FPS across at least 10shots (better all the way until it falls off the reg)
- Pellets or slugs
- Ammo weight
Just my too sents
Edward
Upvote 0
Ed
Not following.
Can you clarify? Please re-read your post and I would like to know what you meant to say.
Thanks
Upvote 0
@tommyb
When I read your post, it seemed to me that you were wondering in a 170BAR regulator set is the best for your Revere.
So, with that in mind I suggested that you tell the forum more about your shots at that setting
Including, fps, pellet or slug weight, etc
And that you post a completer string from 250- 170BAR, and lower
This gives the "guys that know a lot" a good basis for evaluating your tune and making suggestions, if needed.
I hope that clarifies things
BTW
I reread my post, and the only change I would make is
"Just my too sents" would become
Just my 2 scents
Edward
When I read your post, it seemed to me that you were wondering in a 170BAR regulator set is the best for your Revere.
So, with that in mind I suggested that you tell the forum more about your shots at that setting
Including, fps, pellet or slug weight, etc
And that you post a completer string from 250- 170BAR, and lower
This gives the "guys that know a lot" a good basis for evaluating your tune and making suggestions, if needed.
I hope that clarifies things
BTW
I reread my post, and the only change I would make is
"Just my too sents" would become
Just my 2 scents
Edward
Upvote 0
Gotcha. Thanks for clarifying.
I shoot the JSB 18.1 and 15.89g in the Revere. I believe the 18.1g is about 840 FPS and 15.89 at 880 fps approximately. I’m happy with accuracy, but I was surprised Daystate has the reg set so high from the factory.
The cylinder is small, but shot count is not a big priority. It does suck a lot of air though if you shoot a couple hundred pellets at the range.
I’m happy with the current performance, I was just surprised at the 170 BAR Huma reg setting.
Upvote 0
Okee-dokee
You have a great gun in the Revere.
No fuss/no muss
And very accurate
Enjoy!
Last edited:
Upvote 0