EaZy Trigger Fill for PCPs

[tommyb]

Ed (EPG) got me interested in this lil’ do dad. I really like it.

If you are at the range, or at the bench in your backyard and you fill from an air tank several times during your shooting session, take a look at this EzAy Fill Trigger from Edgun. $ 150, not cheap but worth it to me anyway.

While this is not an endorsement, I saw this on a recent AEAC review and Steve demo’d the easy way to fill your PCP air guns without removing or bleeding your fill wip from the gun each time you fill and remove the hose. A side benefit is that you save air, especially if you fill or top off 6, 8, 10 times or more during your session.

Here’s one example. I brought my RAW TM1000x .177 to the range this past week. My GW was approximately at 3600 psi when I started and is currently at around 3300 psi. But, I probably filled it from 150 BAR to 220 BAR about six times. I honestly don’t know how much air it can save, but it appeared to save quite a bit. I only bled the GW tank valve one time, when I was finished. You can leave the Trigger in your gun or remove it, based on your preference. I tried both ways.

I like the idea of using the red EzAy fill trigger vs. loosening the yoke on my Great White. Why? Because it’s simple, and I can fill slow or fast by controlling the EzAy lever which is spring attached. I use the GW tank pressure gauge to stop when I am at max fill pressure on a particular PCP. I also avoid bending over every time I’m behind the bench to fill the gun by reaching for the Yoke on the GW.

AoA and Utah Air have them in stock. Here is a link that describes the features below: There are a few YouTubes that also demo the product.

Edgun EaZy Fill -Trigger | Utah Airguns

Edgun EaZy Fill -Trigger

utahairguns.com

 

[JaceSpace1369]

Ed (EPG) got me interested in this lil’ do dad. I really like it.

If you are at the range, or at the bench in your backyard and you fill from an air tank several times during your shooting session, take a look at this EzAy Fill Trigger from Edgun. $ 150, not cheap but worth it to me anyway.

While this is not an endorsement, I saw this on a recent AEAC review and Steve demo’d the easy way to fill your PCP air guns without removing or bleeding your fill wip from the gun each time you fill and remove the hose. A side benefit is that you save air, especially if you fill or top off 6, 8, 10 times or more during your session.

Here’s one example. I brought my RAW TM1000x .177 to the range this past week. My GW was approximately at 3600 psi when I started and is currently at around 3300 psi. But, I probably filled it from 150 BAR to 220 BAR about six times. I honestly don’t know how much air it can save, but it appeared to save quite a bit. I only bled the GW tank valve one time, when I was finished. You can leave the Trigger in your gun or remove it, based on your preference. I tried both ways.

I like the idea of using the red EzAy fill trigger vs. loosening the yoke on my Great White. Why? Because it’s simple, and I can fill slow or fast by controlling the EzAy lever which is spring attached. I use the GW tank pressure gauge to stop when I am at max fill pressure on a particular PCP. I also avoid bending over every time I’m behind the bench to fill the gun by reaching for the Yoke on the GW.

AoA and Utah Air have them in stock. Here is a link that describes the features below: There are a few YouTubes that also demo the product.

Edgun EaZy Fill -Trigger | Utah Airguns

Edgun EaZy Fill -Trigger

utahairguns.com

May it last you longer than it's lasted most other members. I've wanted one for the same reason that you like yours.But I have stayed away from getting it due to what I have read. Glad you're enjoying yours!

 

[keefd]

May it last you longer than it's lasted most other members. I've wanted one for the same reason that you like yours.But I have stayed away from getting it due to what I have read. Glad you're enjoying yours!

I thought it was the knock-offs that had reliability issues, and that the original was okay - or is that not the case?

 

[Airgun-hobbyist]

I finally broke down and bought one last year. I'll endorse it because it does save a lot of waisted air and is a great concept making refills a breeze. As a disclaimer to the endorsement, it didn't come without it's two small issues I've had to work around... Because of the repeated use and required pressure on the thumb trigger, the thin roller pin bore on the trigger blade wore out and the pin now slides out one side with repeated use (I replaced the pin with something better) . And, unless perfectly setup sometimes the thing doesn't release the air pressure without some trigger manipulation.

 

[WoodWelder]

Wowzer that is expensive?

 

[JaceSpace1369]

I thought it was the knock-offs that had reliability issues, and that the original was okay - or is that not the case?

The reviews I read on here were for the original.

 

[tommyb]

May it last you longer than it's lasted most other members. I've wanted one for the same reason that you like yours.But I have stayed away from getting it due to what I have read. Glad you're enjoying yours!

Can you refer me to the posts of the members who have had issues, and specifically what were they?

Too late for me, I bought one. But, please share the reviews or posts.

 

[steve-l]

It is a great idea, if it works and it fails with pressures exceeding 200 bar. I have bought 3 and every one failed.

 

[WoodWelder]

Can you refer me to the posts of the members who have had issues, and specifically what were they?

Too late for me, I bought one. But, please share the reviews or posts.

Like anything out there, sometimes its the first generation or simply a bad one....Likely have the kinks out by now?

EDgun - EDGun Eazy Fill leaking....

Hello all! I purchased an Edgun Easzyfill unit some 3 months ago. This is an expensive unit, but as many of you have already attested, an absolute pleasure to use. However, when it began leaking air (from the front discharge), I returned it to the dealer, who replaced it. The dealer then...

www.airgunnation.com

 

[JaceSpace1369]

Can you refer me to the posts of the members who have had issues, and specifically what were they?

Too late for me, I bought one. But, please share the reviews or posts.

Thread 'EDGUN PEAZY' https://www.airgunnation.com/threads/edgun-peazy.1311448/

Thread 'Peazy Leaking - Repair Instructions?' https://www.airgunnation.com/threads/peazy-leaking-repair-instructions.1314341/

Like anything out there, sometimes its the first generation or simply a bad one....Likely have the kinks out by now?

EDgun - EDGun Eazy Fill leaking....

Hello all! I purchased an Edgun Easzyfill unit some 3 months ago. This is an expensive unit, but as many of you have already attested, an absolute pleasure to use. However, when it began leaking air (from the front discharge), I returned it to the dealer, who replaced it. The dealer then...

www.airgunnation.com

I hope so!

 

[tommyb]

So, we’ll see how it performs. I will report back if any issues.

 

[Ta-Ta Toothie]

On my 3rd rebuild, purchased 1.5 years ago. The plastic internals seat / valve assembly splits. Should be made out of something stronger like peek.

 

[Raider03]

Makes sense if you're filling a pistol or gun with a small tube capacity, but expensive.

 

[tommyb]

Geez - I thought I was recommending something innovative and “reliable.” I love the concept, and I have always been an ‘early adopter.’

I hope this device proves to be of good quality, but if not I will rectify with my experience and post results.

Nobody should charge $150 if there are too many issues.

We’ll see.

 

[Ta-Ta Toothie]

I love the ease of use, but won't be buying anymore rebuild kits. Hope yours works out.

 

[Firewalker]

I've had mine for 4 years now, rebuild it last year. Eazy-PZ

 

[bigHUN]

I have mine since day one it surfaced. Service it maybe two times without any new parts needed, just re-sealed or adjusted the lever pin stroke.
I like to drop a drip or two of ptfe oil in the line every time I am refilling each of my guns. Helps lubing internal non static orings as well for a long run.

 

[manabeknives]

Can you refer me to the posts of the members who have had issues, and specifically what were they?

Too late for me, I bought one. But, please share the reviews or posts.

Hi Tommy
The big issue i had with this piece is that it has a 300bar burst disk.
If you hook it up to a scuba tank filled to 4500psi, it's going to leak out until stabilized
so you can not fill your rifle beyond the equalization point...so always less than 300 bar
if it is not a problem for you, then disregard
Mike

 

[Avator]

I sprung for one of the originals before the knock off came out. I used it alot for the first year or so without issue. I don't use it much now because I don't use my tanks much anymore. It worked just fine last time I used it.

 

[tommyb]

Hi Tommy
The big issue i had with this piece is that it has a 300bar burst disk.
If you hook it up to a scuba tank filled to 4500psi, it's going to leak out until stabilized
so you can not fill your rifle beyond the equalization point...so always less than 300 bar
if it is not a problem for you, then disregard
Mike

Thanks Mike. Yeah, I’ve now read plenty of user experiences with rebuilding the EzAy fill, replacing parts, et. Al. I don’t want any part of that. It seems It gets mixed reviews. I saw the exploded diagram, ugh!

A question for you below.

So my Great White tank gets filled to 4500-4700 psi typically by my Dive shop. If I fill guns that are less than 300 BAR, (even though my tank is at 4500 psi), I should be OK right? I have a Revere and a .30 Boss that take a 250 BAR max fill.