follow up shots or double-taps are easy. you have to slow this down to see all 8 shots, and this was my first attempt after zeroing.
https://www.youtube.com/watch?v=Od8kOn29J1c
Upvote 0
EDgun Edgun Leshiy 2
- Thread starter Navnesen
- Start date
follow up shots or double-taps are easy. you have to slow this down to see all 8 shots, and this was my first attempt after zeroing.
https://www.youtube.com/watch?v=Od8kOn29J1c
Great shooting! - yes you can do some mighty fine shooting with a red dot, especially if the dot fits so you see the target as a halo around the dot
Here's my best no wind 10 shot group with the Classic
Upvote 0
Finally got some trigger time with the .25 . Using the 3x Vector Calypos prism sight from 15 to 45 yards it was near impossible to miss the 1” targets . 4 shot groups with the 25.4 grain JSB average 3/4” at 900 FPS and the MKII heavies slightly better at 5/8” at 780 FPS . Shot count with a 350cc bottle is right at 40 shots per fill while still on the regulator , that is filled at 250 bar shooting down to 135 bar which is plenty for a couple days hunting. I didn’t get a chance to shoot any cast BBT as I forgot my sizing kit. Hope to get out again to put them to the test. I ram a few dry patches through the barrel after about a tin of pellets , this barrel is very nicely finished and the two patches came out very clean. Almost as though the barrel was polished from factory.
Upvote 0
i have a .22 and this is with a 1/2 a tin through it, but if you are curious what it might look like and don't have a scope....
Upvote 0
After 6 weeks of reading and watching the videos here, this is what I have come up with so far. At 75 yds this thing is a laser ! Next is the moderator/shroud swap. Maybe the 450mm barrel. I need to move the bipod forward and 45 a red dot or Eotech holo. The bell is about to toll for a few coyotes and feral hogs in central Florida. ( And maybe a few Iguanas down south )
Thanks to everybody here for the help and input even if you didnt know you were helping : )
Thanks to everybody here for the help and input even if you didnt know you were helping : )
Upvote 0
After 6 weeks of reading and watching the videos here, this is what I have come up with so far. At 75 yds this thing is a laser ! Next is the moderator/shroud swap. Maybe the 450mm barrel. I need to move the bipod forward and 45 a red dot or Eotech holo. The bell is about to toll for a few coyotes and feral hogs in central Florida. ( And maybe a few Iguanas down south )
Thanks to everybody here for the help and input even if you didnt know you were helping : )
what kind of results are you getting with the FX Hybrid Slug, .30 Cal, 44.5 Grains (accuracy and velocity)?
Upvote 0
Wanted the accuracy to zero the scope and use the rest on little stuff like starlings and rabbits. I have Nielson 54.5's for small hogs and coyotes. The Diabolos are decent but just dont hit as hard as the Nielson slugs. Not really sure but maybe turkeys and iguanas. From what I have read and seen on video, there are very few slugs that can match their accuracy. The FX just were the easiest to get my hands on.
Upvote 0
Seems like all pellets and slugs are hard to get right now. Just received one pack of the FX Hybrid Slug, .30 Cal today looking forward to test in them in my custom 600mm FX STX barrel, in theory they should work well. I tested NSA slugs 43.8gr 47.2gr, 49.5gr and Vermit Knocker 50gr. All performed good at speeds of 960-1020fps. The L2 can make a lot of power so I would like to test some of NSA’s heavier slugs, I believe the 65gr will fit the L2 mags. I also would like to get a .30 450mm barrel.
Upvote 0
https://m.youtube.com/watch?v=LE_f8Dvwaa0 Ed
In this video, ED talks about how he doesn’t like to have a gauge opposite of the reg adjustment on the new REPR but instead suggests to place a gauge where the bleed screw goes (see screen shot below).
has anyone tried this yet? What gauge would fit there?
Upvote 0
My question how do you A-line the REPR Plenum and Regulator in different positions? I noticed in the videos the gauge port and the regulator adjuster are on different sides and at different angles.
Upvote 0
you have to shoot the gun a few times to get the new pressure in the plenum if you turn it down, but if you're increasing pressure, it shows right away.
Upvote 0
My question how do you A-line the REPR Plenum and Regulator in different positions? I noticed in the videos the gauge port and the regulator adjuster are on different sides and at different angles.
Bleed the air on your L2 then use hex bolt under the top butt stock cover to adjust the tube alignment.
Upvote 0
Not hard to get, just hard to pay that much! The JSB exact, predator poly mags and Hades all in .30cal are available on Amazon right now
Upvote 0
Not hard to get, just hard to pay that much! The JSB exact, predator poly mags and Hades all in .30cal are available on Amazon right now The hybrid slugs are everywhere
Upvote 0
My question how do you A-line the REPR Plenum and Regulator in different positions? I noticed in the videos the gauge port and the regulator adjuster are on different sides and at different angles.
Bleed the air on your L2 then use hex bolt under the top butt stock cover to adjust the tube alignment.
Maybe I’m missing something but it looks to me that the threads attaching it to the valve would control where it’s indexed.
Upvote 0
My question how do you A-line the REPR Plenum and Regulator in different positions? I noticed in the videos the gauge port and the regulator adjuster are on different sides and at different angles.
Bleed the air on your L2 then use hex bolt under the top butt stock cover to adjust the tube alignment.
Maybe I’m missing something but it looks to me that the threads attaching it to the valve would control where it’s indexed.
My bad, that’s was for butt stock alignment.
Upvote 0
Pushed these through the .25 350mm alpha barrel today. The left is NSA 34.9 gn the right is FX hybrid at 26 gn. It was actually a pretty tight fit, but I don’t see any markings from the valleys but there is pretty good engagement of the rifling. They will fall out of the front of the magazine, but if you leave the mag in place you can load it without them falling out. They cycle fine since there is only the machined surface for them to ride on.
The NSA averaged 860 over 8 shots.
The FX averaged 959 over 8 shots.
Oh and does anyone know the twist rate of the rifling?
Upvote 0