EDgun Edgun Leshiy 2
- Thread starter Navnesen
- Start date
The big picatinny mag looks like coming from airsoft accessories, and the L2 holder is 3d printed
Upvote 0
The brake is from the edgun leshiy shop in spain. Its the trilug version so can be attached and removed with a quarter turn, just like the bohemoth. The mag holder actually for a the AGT Vixen. I 3D printed extra parts with a small disc magnet inside so I can attach L2 mags to the side of it
Upvote 0
The brake is from the edgun leshiy shop in spain. Its the trilug version so can be attached and removed with a quarter turn, just like the bohemoth. The mag holder actually for a the AGT Vixen. I 3D printed extra parts with a small disc magnet inside so I can attach L2 mags to the side of it
Sweet. I like that Trilug brake.
I like making my PCP's louder, one of my neighbors pissed me off a couple years ago so unless I don't wanna use ears, I always shoot in the back w/o moderators.
Last edited:
Upvote 0
What would cause a loss of power and inconsistent velocities in a L2? My .22 was a tack driver shooting 18gr JSB Heavies at 875fps with very little variation. I've just noticed the accuracy went down, with more fliers. Chronoed the gun and surely enough, velocities now vary wildly between 790 and 840 fps on one mag from the same exact tin of pellets it was originally tuned on. Cleaned the barrel, checked mags, replaced the puck, no effect. Any advice before I tear down the gun and inspect the valve and the reg? This is a non-REPR so no plenum gauge.
Upvote 0
Hmm. This is a franken-Leshiy. The forward plug with the valve is relatively new, ~1K rounds or so. Probably 5-6K on the reg.
Upvote 0
yeah, that seems low for a need of rebuild. Then again, if it’s frankensteined, one of the orings could have been deformed or nicked going together at some point, and just took a little time to completely fail.
Upvote 0
Somewhere last summer I had a similar...somehow in the airpath a very small micro chip was travelling and stuck the Reg piston. Luckily when I started searching for a troublemaker I toke my L2 into bits and pieces and inspect every part with a high magnification jewellery loup this how I find it, I washed every piece of the L2 with 99% IPA and blew dry with air, replaced all OEM orings and relubed. That was a fresh start.
Upvote 0
So I thought I'd check the front plug before I mess with the reg. Didn't see anything wrong, but whatever it was, the problem was there. Took everything apart, cleaned, re-lubed, replaced the valve pin bead for a good measure. All back to normal now. Go figure.
Upvote 0
Are you able to fold and lock your rifle with this bottle and saber tactical picatinny to picatinny rail? I tried with 470cc bottle from edgun spain and that rail. couldnt make it
Upvote 0
Did you install the 16mm pin lock?
“A 16mm pin lock is needed if your idea is to install this bottle on the Leshiy 2 and have it locked while folded. If you already have a Behemoth or a carbon fiber handguard, then you most likely already have the 16mm pin. If you don't care about locking it while folded, or plan on using the 470CC bottle with a pEaZy, then you won't need it.”
Last edited:
Upvote 0
...
I like the look of the original can, if anybody have one laying around and not using it and wanna trade pls pm me... I don't care for the internals, but I would like to get the shell.
I like the look of the original can, if anybody have one laying around and not using it and wanna trade pls pm me... I don't care for the internals, but I would like to get the shell.
Upvote 0
Yes I did. I also had to add 2 spacers on the other side of the latch. Rifle would lock without Saber Tactical rail with 470cc bottle installed. But with that arca rail I have no luck locking it folded. Arca rail on the wayDid you install the 16mm pin lock?
“A 16mm pin lock is needed if your idea is to install this bottle on the Leshiy 2 and have it locked while folded. If you already have a Behemoth or a carbon fiber handguard, then you most likely already have the 16mm pin. If you don't care about locking it while folded, or plan on using the 470CC bottle with a pEaZy, then you won't need it.”
Upvote 0
Does anyone know if i can replace part 31 LSA242223 with something generic from the hardware store?
I currently do not have the original part so cannot see what kind of material is.
I currently do not have the original part so cannot see what kind of material is.
Last edited:
Upvote 0