FX Fx dynamic expres 700 cal .25 And talking about hammer weight
- Thread starter darknes
- Start date
My .30 cal Dynamic comes stock with the 6mm, I emailed FX and asked to be sure... So I'm sure the .25 would as well...
I'm not sure if you can post links here or not, but if you look up Panthera 8mm hammer you will find it...
Upvote 0
FX Maverick, Wildcat, Dreamline, Crown, Boss Hammer Weight Tuning Set
FX Maverick, Wildcat, Dreamline, Boss Hammer Weight Tuning Set
www.huma-air.com do you think this?
Upvote 0
Yes the heaver of the two weights in the tuning kit is the 8mm HammerFX Maverick, Wildcat, Dreamline, Crown, Boss Hammer Weight Tuning Set
FX Maverick, Wildcat, Dreamline, Boss Hammer Weight Tuning Set
do you think this?
Upvote 0
so it will fit without problems?
do I use the original spring or do I have to get another one?
Upvote 0
I think the original spring is good the 8mm hammer is 14 grams and the FX heavy hammer is 16 gram
Upvote 0
Hammerweight 8mm 13.20g
<p>Hammerweight 8mm 13.20g</p> <p><iframe width="560" height="315" src="https://www.youtube.com/embed/dGVsWLW2Rw0" title="YouTube video player" frameborder="0"></iframe></p>
europeairguns.com 
Hammer Tungsten 26.5g 8mm
<p>Experience the unleashed power with the introduction of a game-changing upgrade: the Tungsten Hammer!</p> <p>When it comes to shooting slugs, their additional weight and surface area necessitate higher pressures for effective propulsion. Additionally, longer barrels offer increased speed...
europeairguns.com Upvote 0
Tungsten hammers were bending the valve pins on the Panthera's, I know FX beefed up the middle of the valve pin some, but they don't recommend using the tungsten hammer anymore, so I wouldn't go any heavier than the 8mm...
Upvote 0
I don't quite understand why FX uses hammer weight changes opposed to a valve that could be adjusted...their current valve could with a proper engineering tweak...
26.5 grams is a ton of hammer on a balanced valve that normally uses much less, the only reason something would bend in the 'valve train' is being over driven to the point of being bound lol, do they even engineer these things or do they slap stuff together and let consumers give it a go?
-Matt
26.5 grams is a ton of hammer on a balanced valve that normally uses much less, the only reason something would bend in the 'valve train' is being over driven to the point of being bound lol, do they even engineer these things or do they slap stuff together and let consumers give it a go?
-Matt
Upvote 0
I don't want to use a tungsten hammer. I gave an example of hammers and their weights here. I would like to use an 8mm hammer but I can't find any in Europe. I wrote to huma air for a recommendation and they replied that I should use a Tungsten hammer but at the minimum spring setting. I was just asking if I could use their set of hammers that they sell on Maverick.
Upvote 0
Talon Tunes has it in stock if they ship internationally. It is pricey through them though... https://talontunes.com/shop/fx-panthera-8mm-hammer/
Upvote 0
yes, to the Czech Republic 35 dollars Hammer and postage + duty and VAT is around 150 dollars
Upvote 0
Not sure why that is so expensive through Talon Tunes, Tom has a listing for it at High Pressure Pneumatics for 8 bucks, but it's out of stock...
Upvote 0
it's hard to say why some are so expensive, but here they are mostly only available for pre-sale
Upvote 0
Hammer Weight / Spring Guides | FX Airguns | Crown, Dreamline, Maverick, Wildcat | eBay
Find many great new & used options and get the best deals for Hammer Weight / Spring Guides | FX Airguns | Crown, Dreamline, Maverick, Wildcat at the best online prices at eBay! Free delivery for many products.
www.ebay.co.uk
I found this link. I finally know how it's all meant. therefore, I am able to actually make it all at home and in different weights.
Upvote 0
I couldn't do it and I took out the hammer, measured, weighed, drew. the result is 12.1 grams
Upvote 0
