Tuning Need a line on where to purchase a dual transfer port with low-side port

[Revoman]

Checked 910, no gots and HUMA doesn't make a dual port with the low side port at 180° that I can see. Anyone know where I might find one for a .25 caliber FX Impact MKII please lemme know.

Thanks and shoot straight!

mike

 

[Airgunmann]

You could drill a small hole on the other side of your existing one and step it up till you get what speed you want. Just a suggestion you looked at both the places I would have only other place would be contact fx I'm sure they will sell you one they sold me a 500mm shroud when I couldn't find one I just sent a email and they did so over emails otherwise I don't know

 

[biohazardman]

 

You can't just drill a hole in the other side. You would also need to mill the slot to align the barrel as well.

I just sold one on the classifieds got it here but they be sold out of the .25 sorry. 

https://910airguntuningandrepairsllc.com/products/fx-stx-barrel-dual-tranfer-port



FX got the last parts I ordered to me in just a few days though so you might want to just order from them directly.

19670 Barrel inlet .25

Online parts order form;

https://www.fxairguns-usa.com/parts-order/

 

[Revoman]

Thanks for the information. I tried calling FX USA without luck, no answer, so I emailed them with a request for more information.

I also emailed 910 asking the same question.

Shoot straight!

mike

 

[Airgunmann]

You can't just drill a hole in the other side. You would also need to mill the slot to align the barrel as well.

I just sold one on the classifieds got it here but they be sold out of the .25 sorry. 

https://910airguntuningandrepairsllc.com/products/fx-stx-barrel-dual-tranfer-port



FX got the last parts I ordered to me in just a few days though so you might want to just order from them directly.

19670 Barrel inlet .25

Online parts order form;

https://www.fxairguns-usa.com/parts-order/

True I forgot about the locating slot oops sorry

 

[Airgunmann]

I have a regular 25 but no low power hole in it and normal probe since I changed to Huma one 

 

[biohazardman]

Thanks for the information. I tried calling FX USA without luck, no answer, so I emailed them with a request for more information.

I also emailed 910 asking the same question.

Shoot straight!

mike

It's getting close to Christmas and with the supply lines so screwed up already I would imagine it's crazy for all of the vendors about now.

Good luck.

 

[Revoman]

Yeah, still awaiting replies from both 910 and FX USA after emailing late last night (West Coast). Again, I thank you for your helpfulness!

Shoot straight!

mike

 

[Scotty1]

Mike, if you just fill out the parts request form and submit it, they will typically respond the next day with a quote and invoice, you pay and parts are sent. I’ve had no problems so far…

 

[ChRiSiS]

Mike, if you just fill out the parts request form and submit it, they will typically respond the next day with a quote and invoice, you pay and parts are sent. I’ve had no problems so far…

+1

I’ve done this many times and it has always worked flawlessly as described above.

 

[Revoman]

Thanks Scotty1 and ChrRISIS. I would anticipate that since this seems to be an aftermarket part, FX likely won't have but the stock product. If that's all there is out there, then I'll get one to tide me over until the aftermarket is available from 910.

Shoot straight!

mike

 

[Scotty1]

You may try here. 

Apologies, didn’t notice you were after a low port as well, pre-java over here. I can’t imagine it being too hard to drill and notch for the low port. 

 

[Airgunmann]

I thought that the high and low sides were a factory part and come on the newer barrel set

 

[biohazardman]

The dual hole high power and single hole low power units are stock FX parts these days on the .22 and .25 barrels.

 

[Scotty1]

I wasn’t sure because I have the superlight barrels for my Crown. 

 

[Revoman]

Thanks all. I have emailed FX USA as suggested on Friday, no word back yet.....tapping toe.

mike