O-ring woes

Jump to latest Follow Reply
Peashooter

Peashooter

Member
Apr 9, 2021
3,726
3,024
Denmark
Okay so i have officially lost it, i simply are not able to put a 6X1.5 mm Oring into the adjuster on the Two valve.
Any of you guys have a good idea as to how it is done ( yes i have tried to put something in the hole so the O-ring at least do not " fall " down below where its supposed to go.

But i am still out of luck.

Cursed O-ring.jpg
 
  • Wow
Reactions: Firewalker
Peashooter said:
Okay so i have officially lost it, i simply are not able to put a 6X1.5 mm Oring into the adjuster on the Two valve.
Any of you guys have a good idea as to how it is done ( yes i have tried to put something in the hole so the O-ring at least do not " fall " down below where its supposed to go.

But i am still out of luck.

View attachment 504107
Click to expand...
Your on the right track. I'd put the 2 valve in a vise and put a dowel up the backside until flush with the bottom of the groove.

Use a sticky silicone grease, get some in the groove and oring, use a hemostat to hold and push the edge of the oring into the groove then use another dowel to push the remaining loop into the groove.
 
  • Like
Reactions: Star7
Upvote 0
The hole is a dead end so have not been able to do my breed O-ring approach.
But i have filled it in with something i can fish out after install, well i assume.
But ill be damned if i can do it anyway,,,, it is extremely demolishing, have just tried for a hour or so with a " wet " O-ring, and still not there.
It feel like the O-ring are like 1-2 mm too large in OD, but it is of course right size, i have triple checked that.


ON the + side, unless customs burn me,,,, AGAIN :sleep: it look as if i can pick up a nice Oneleaf NV500 scope tomorrow / later today CUZ it is 3:30 in the morning in little Denmark. Maybe also the GD Best fittings parts i paid my customs on Thursday.

Even more + Tuesday look to be 0 wind, well at least for a hour or so in the start of the afternoon.
 
Last edited:
  • Like
Reactions: Firewalker
Upvote 0
Peashooter said:
The hole is a dead end so have not been able to do my breed O-ring approach.
But i have filled it in with something i can fish out after install, well i assume.
But ill be damned if i can do it anyway,,,, it is extremely demolishing, have just tried for a hour or so with a " wet " O-ring, and still not there.
It feel like the O-ring are like 1-2 mm too large in OD, but it is of course right size, i have triple checked that.
Click to expand...

I'll give you the option of sending it to me and I'll put it in for you.

I'm 100,000:0 so far! 🤣
 
Upvote 0
well it is my spare valve so the Two are still shooting, Epic also providing me with another valve. ( 3 now )

I think i am THE Two shooter that have put the most lead thru his rifle, i assume others will hit the same wall i am banging on at some time, i will estimate i am like 20.000 shots into the rifle, easy when you do like 3000 shots a week or maybe a little more in the summer time.

But i am pig headed now and i will get the damn thing in if i have to use a sledgehammer.

The " bump O-ring that sit at the top of the Jet ( #8 ) look like this the last one i took out ( 5 X 1.75 mm ) But that one is a breeze to replacs as it is a outside ring,,,, which i am thinking about replacing with a 5 X 2 mm and maybe something harder than 90 shore

5X1.75.jpg


2valve.jpg
 
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu