Thanks, WMā¦ā¦I always clean (and polish) my barrels first thing. I wonāt need the moderator as Iām shooting in a mountain location. And I might just leave the probe in the gun.
Upvote 0
Uragan 2 šš¼
- Thread starter Ctkny
- Start date
Things that will be needed for me in order to buy another uragan . I have 4 U1 and i really enjoy them all.. this will be then U3 ..Wright now AGT guns have power enough...longer magazines so longer slugs could be shot without problem.. in .22 n .30 and the external adjustability for the regulator and hammer..thicker barrels or a factory tensioning sistem for the 600mm and 700mm barrels... I certainly would like to buy .22 n .30 in 700mm
Upvote 0
Quiet with factory shroud, whispers with moderator. Fill probe needs adapter like shown in this photo, after you unscrew it from the goofy bottle-feed contraption AGT sends with their airguns. Top of photo is one-piece unit I haven't found yet for U2, middle and bottom photo shows similar probe setup and adapter you'll need.
Upvote 0
AGT e-mailed, having hard time believing gun got out of the factory without Pinching Screw or Axis Pin, said next to impossible. Asked for photos and serial number. Replied with these photos, I don't see any Pinching Screw or Axis Pin, only a flat-topped steel pin low in the threaded hole, with no obvious way to remove. WM
Upvote 0
Don't want u too take it the wrong way. You sure that's not a setscrew?? It's hard to see if it is or not.
Upvote 0
Wish it was, sits way down in threaded hole, just a flat-topped round peg. Here's another picture showing better how deep.
Upvote 0
Did you find your Pinching Screw and Axis Pin to have metric Allen head or screwdriver slots? I know second photo looks that way, nobody wishes it were so more than me, just round pin inserted from bottom.
Upvote 0
Yeah, what I thought, just no way, a flat round end of a pin. I bet your Pinching Screw and Axis Pin filled up that threaded hole, too, and never left that many exposed threads. I even have same set of metric Allen wrenches as you show in photo. I'm not using gun till AGT gives an answer, don't know what damage cocking will do with pin installed. Would never have known if preferred left-hand cocking. WM
Love the carbon shroud would really like one for minelove our one, only .177 compact sub 12 lbft but what a gun fantasticpic with a few sub 12 Airgunners mods on
View attachment 320363
View attachment 320361
Upvote 0
Where can i get a carbon shroud like that from? Looks awesomelove our one, only .177 compact sub 12 lbft but what a gun fantastic
View attachment 320363
View attachment 320361
Upvote 0
Shooting a recently purchased Uragan 2 700 mm barrel. 30 cal. with a Talon Tunes power mod. FX hybrid slugs 107 FPE. Just shot a 15 shot group with it 2 days ago @ 75 yds. The group could be covered with a dime. Shoots JSB/FX pellets great but the hybrid slugs are amazing. It pushes 44.75 gr. pellets on average of 1046fps.
Upvote 0
URAGAN 2 Owners Trigger adjustment??
Anyone out there familiar on how to adjust the trigger . The second stage has a noticeable amount of creep in it before it fires. I removed the stock and can clearly see the sears are engaged by nearly a hair but still has creep. Drives me crazy. Would like to set it up sub 1 lb. Owners manual offers no information on how to adjust.Any info. greatly appreciated.
Anyone out there familiar on how to adjust the trigger . The second stage has a noticeable amount of creep in it before it fires. I removed the stock and can clearly see the sears are engaged by nearly a hair but still has creep. Drives me crazy. Would like to set it up sub 1 lb. Owners manual offers no information on how to adjust.Any info. greatly appreciated.
Upvote 0