Umarex Where to get Umarex O-ring

[MikeyJ]

Hi all,
I have a Umarex Walther Reign and I noticed the o-ring on the pellet probe rod (see photo - I think that's what it's called), is missing. This explains why I'm getting a blast of air in my face when I fire the rifle. I'm not sure how it went missing, but it did. I located the part # (465.22.01.2) and called UmarexUSA to ask if I could order a replacement. They told me I would have to send the rifle in for them to repair it. This is pretty silly. It's a simple O-ring that measures 3.5mm x 1.2mm that I could replace in 5 seconds! So, now I'm stuck. Does anyone know where I can find this O-ring? Thank you!
Mike

 

[WNYBill]

Amazon or a good hardware store.

 

[MikeyJ]

Thanks, I'll check.
I'm not sure now what size o-ring it is - the parts diagram also shows a 4.0mm x 1.5mm. That size is easier to find.
Mike

 

[oledawg]

Thanks, I'll check.
I'm not sure now what size o-ring it is - the parts diagram also shows a 4.0mm x 1.5mm. That size is easier to find.
Mike

Captain O-Ring - Firearm & Air Gun O-Rings

Captain O-Ring offers a full line of o-rings for firearms and air guns. Our o-ring kits include parts for Remington shotguns, crosman air guns (pistol and rifle), and more!

www.captainoring.com

 

[MMCM13]

5 x Walther Reign Breech Bolt Probe O ring Seals - Bagnall and Kirkwood Airgun Spares

This listing is for 5 breech seals for the Walther Reign air rifle / airgun. These seals are easy to replace and commonly wear. Worn seals can result in loss of power and accuracy. Choose .177 (4.5mm) , .22 (5.5mm) or .25 (6.35mm) caliber

spares.bagnallandkirkwood.co.uk

 

[MikeyJ]

Thanks. I saw that . I didn’t want to have to go across the pond, but that may be my best option, despite the expensive shipping.

 

[Scotty1]

I would try the 4mm x 1.5mm, and silicone on the o-ring is helpful.

 

[MikeyJ]

I would try the 4mm x 1.5mm, and silicone on the o-ring is helpful.

Ok. Is 4mm the outside diameter of the ring?

 

[Scotty1]

That’s the inside. What caliber is this?

 

[MikeyJ]

.22

 

[Stubbers]

These are 3.5OD x 1.5ID and 1mm CS, you need to give specific dimensions though as I am unsure if you mean 1.2MM ID or Cross section.

3.50$ with free shipping if you find what you need thru this ebay seller.

1.5mm ID x 3.5mm OD x 1mm thick O-ring. Buna-70. Quan 5.. | eBay

Buna (nitrile) material.

www.ebay.com

Here is 4mm x 1.5mm

1mm ID x 4mm OD x 1.5mm thick O-ring. Buna-70. Quan 5.. | eBay

Buna (nitrile) material.

www.ebay.com

 

[MikeyJ]

Captain O-Ring - Firearm & Air Gun O-Rings

Captain O-Ring offers a full line of o-rings for firearms and air guns. Our o-ring kits include parts for Remington shotguns, crosman air guns (pistol and rifle), and more!

www.captainoring.com

Called these guys snd talked to John. Super nice guy. There’s a $10 minimum order, so he’s sending me 8 of the 4.0mm rings for just over $10, including shipping. Thank you!!!

 

[oledawg]

Called these guys snd talked to John. Super nice guy. There’s a $10 minimum order, so he’s sending me 8 of the 4.0mm rings for just over $10, including shipping. Thank you!!!

You’re welcome glad it helped.

 

[MikeyJ]

 

[Scotty1]

I would think it would be 2.5mm x 1.5mm or 005. The outside dimension must be close to 5.5mm

 

[MikeyJ]

I hear ya. It’s confusing. I’ll have to see if what I ordered works. If not, I'm back to square 1.

 

[MikeyJ]

Well, I messed up, and it’s because I failed to correctly read the German parts diagram. The 4.0x1.5mm o-rings are too large- they’re for the .25 caliber model. I needed 3.5x1.2mm for my .22 caliber. Captain O-Ring was out of stock on the 3.5s, but I found them at Oringsandmore.com. 25 for $1, plus $7 for shipping. They work perfectly!
Thanks again folks…