Air Arms Utah Airguns Pyramyd AIR FX Airguns Daystate Diana Airgun Depot Edgun West Palm Beach Airguns DonnyFL: PCP Air Rifle Shop and Airgun Moderators The Pellet Shop
Saber Tactical Optisan Side-Shot Scope Cam NE Airguns Baker Airguns AGS Topgun Airguns Predator International Huben Airguns Huma-Air Shooting Supplies Hurricane Luftvapen AEA Precision Airguns H&N Impulse Air ZAN Projectiles Hawke Optics Airforce Airguns Stud Mag Loader RX Target Systems Sports Match Scope Mounts Altaros Banner CTA Thomas Air Hatsan USA Georgia Air Guns Skout Airguns RAW - Rapid Air Works Nielsen Specialty Ammo Patch Worm Weihrauch Sport Talon Tunes Airgun-Revisions JTS PARD ST7 PPP RTI AirStryk Industries Macavity Arms
  • AirNGasman
    Great information, H! Knowing the OP, who is not a lot younger than me, my primary point was "totally self-contained". I can't see...
  • Kerndtc
    This listing has been renewed
  • R
    I was one of the new guys at the match... Had a great time and everyone was very helpful and fun! Thank you so much to Wes C for taking...
  • R
    Ricklin replied to the thread Where to find??.
    Gerry52 hit the nail on the head. O-rings require 2 dimensions the inside diameter and the cross section. All O-rings are listed and...
  • K
    Have you made adjustments to lighten the trigger? On both my Crown MK2 rifles I have made adjustments to really lighten the trigger and...
  • AirGoon
    The Colonial Airgunners have considered the June 8th issue and have collectively decided to cancel our Field Target Match on June 8th...
  • AirNGasman
    AirNGasman replied to the thread To Strip or Not To Strip.
    I've had good luck enough with their pre-owned guns to believe AoA offers conservative condition descriptions and grading of pre-owned...
  • R
    rcs9250 replied to the thread What’s your favorite target?.
    Darn it, now I can’t wait for my garage door spring to break. 😂😂 Oh what have I just done to myself.
  • Impact701
    Impact701 replied to the thread FX DRS parts.
    I have wondered the same thing.
  • PowderBurnt
    The Dodge Ram vans aren't too expensive, but I hear they are loud. Gotta insulate to deaden the noise. Sam in Sacramento had a good one.
  • G
    I picked up my m3 from UA...the one thing I regret is not having them tune it. Would have saved me a LOT of time and more than worth it...
  • B
    This listing has been renewed
  • Goldwing
    I'm not getting engagement of the safety, presently have the screw clockwised in pretty deep, anymore might loose the grub screw Any...
    • IMG_2802.JPG
  • humbled.ag
    Great vans when running. The egr valves break every 20k or so and are perpetualy out of stock. It's a terminal issue known to the...
  • J
    All original
  • Avator
    Yep thanks... If I get one I would rather it on a short stand/tripod on the bench than on the gun.
  • G
    Gc265 replied to the thread FX M3 to touch or not to touch.
    I second this experience as does a friend with m3...they fluctuate.
  • R
    Ricklin replied to the thread Decided on a PCP....
    Fully agree, the Blitz needs a bigger can. The cyclic rate is crazy high, a 21 round mag dump takes about two seconds. The Ronin does a...
  • AirNGasman
    Mercedes Sprinter- "Where (totally self-contained) COMFORT meets adventure". https://www.ultimatetoys.com/sprinter-conversions/ .
  • JaceSpace1369
    Not today, but on Wednesday, I met up with a member and sold him my akela .177, great guy!
  • Bear-of-Grayling
    I saw that one on AOA. I’ve gotten a few from them. Two were winners and one went back. Their descriptions are vague at best. Good luck...
  • JaceSpace1369
    Okay, well the ones I shared are under 1lb so they should be a great option for ya, plus they have a 5yr warranty.
  • Peashooter
    Finally signs of life from the US O-ring supplier, they have gotten the missing sizes in and have shipped a fat envelope to me. Hope it...
  • Justaguy
    Justaguy replied to the thread FX DRS parts.
    They have all of the parts to change my .25 over to a .177. I would prefer to order from the states but that does not seem to be an...
  • AirNGasman
    AirNGasman replied to the thread To Strip or Not To Strip.
    I noticed that too. FWIW, I've lightly darkened some existing grain streaks with dye to exaggerate them, but adding grain that doesn't...
    • 1744993400189.png
  • Filter