Anyone know where I can source one?

Hi all!

I hope you're doing well.

I'm just looking for recommendations for a reasonably priced, consistent dB reader for my Marauder. I figure it doesn't need to be as overkill as an actual firearm decibel test setup, just something inexpensive but trusted off of Amazon would be great.

Anyone here with a solid recommendation based off of experience already?

Thank you!

Bonjour, huma air already offers the regulator for the m4 impact. An anticipation of future problems with the original m4 regulator?

Has anyone tried the DRS Pro Match trigger in the dynamic platform? Is it possible?

Can anyone recommend these rings?

I need help deciding on which airgun I should get my budget is flexible and I want something upgradeable and am planing on linking and hunting small game

Does anyone know of anyone selling pre ported part 66? Or just the part alone?
I'm not having much luck finding it, given I am on a state farm computer and many things are restricted.

Hello guys. I'm owning wildcat MK3 and everything was perfect until I decided to play a bit with my gun. This is what I did.
I increased reg pressure from 90bar to 110. Installed pin probe and heavier 13gr hammer. After all of this changes the power of my gun increased from around 40 joules to around 57. And here is where strange things start to happen. My power adjustment wheel was not making any difference in velocity speed. Further more, at some point when I played a bit with adjustment screw I got higher velocity on setting 1 than on 7. It should be the other way around. Then I decreased a bit regulator pressure back to 100bar and I switched back to oryginal hammer. Now it doesn't shoot at all. It looks like some air is getting to the barrel. I can hear some air released from barrel when takie probe back from the barrel with cocking lever. To release remaining in barrel slug I installed back the heavier hammer and it shoots back again. I changed to lighter and it's not shooting as the hammer would not have enough power to open the valve. Do you have any idea on what can be wrong?

Hello! Help with the firmware on the pard 008lrf . Firmware PARD_EN 20191104_R43.V1.27. If possible, send it. Sapasibo.

I just cannot figure out how to properly load a CS4 grease pot
i would like to see a picture of where exactly the grease and the rubber diaphragm go.
And how to retract the screw threads that force the gease into the compressor
Apologies
But sometimes simple things confound me
Thanks
Edward

Just took the rifle out to shoot some, First shot sounded different and no impact on target, Small target, tried another with same effect.
My fx chrony did not respond either. looked at pressures, found Rifle at 215b ok but regulator was maxed out. I degassed the rifle and got on here to see if anyone has an idea whats goin on. regulator has been set at 100 for at least a year now.

Thanks
Grump

Bone stock Notos and as my first mod I did the FX 500mm barrel kit. I chose the superior heavy liner as I plan to mainly shoot slugs. I haven't touched anything else but the barrel swap.

So I was shooting 15.4 gamo pellets @740ish and 23gr NSA slugs @ 650ish. After the 500mm kit I lost quite a bit of speed. The 15.4s are 660ish now and the 23gr are 550ish.

Any one have an idea as to why? More curious as to understanding why the loss in speed.

I plan to fully port and big bottle/reg swap too along with custom spring and hammer stuff too at a later point. So I know I'll pick up speed at a later point.

Have the perfect birding/ratting ammo,
FX 25.4/exact king 25.39 at 885-895 same hole groups out to 70 1± moa @100

Been experimenting with slugs and velocities.

This is the 600mm 1:24 stx superior

HYBRIDS hold really tight but only 60y and in. 1.25-1.5moa at best @ 100 .. for rabbit or beaver sure.

SLUG HPII 30gr so far best results I've had with a slug. 0.25mil groups at 25-65 about the same at 100. That's at 880fps which is where my barrels sweet spot seems to be.

ZAN 26.5 just no. Everywhere. 1" @35
Zan 28. Better but about the same to marginally looser grouping than Hybrids
Zan 30 at 840 sure.. but what's the point at that speed? I can shoot heavy mk1 at 890 with superior results
NSA .249 26.8. DISH no no all over
NSA 28 .249 Dish. All over.
I realize stx superior isn't meant for heavier slugs so I've kept it under 34.

JSB SLUGS worth it? Anyone have anything else they've had surprisingly good performance with?

I wish Hybrids worked better, if I was within 70 for everything that'd be amazing because those things almost always leave rabbit, squirrel, beaver SUPER DRT, ESPECIALLY at 925 ±5

idk if this is co2 or air and I can't get the end cap off that they say use a coin with. Also estimated value? I have no use for it, but it's neat someone could appreciate it!

Hello guys,

So today i finally got my Hatsan Sortie to fire, i fired about 50 rounds and it started skipping a few shot's. Now here is where the problems began, i put some gun lube on the action and then ofcourse ran the action (without firing). However, i forgot that i left the magazine in the gun and it pulled back each time and ready'd a new round. I did this pretty fast and after about 7 times (or 7 rounds shoved in the barrel) i realised that i made a huge mistake. Now there are 9 rounds in the chamber/barrel and the mag is empty so the bolt will now no longer go all the way forward, i can't take out the mag because the is a round stuck in between the chamber and the magazine and the gun is filled with air so i also can't take it apart because ut will probably blow up.

Now i am very technically inclined so i know my way around small parts and such but my brain can't think of any solutions for this problem, for reference this is what i have tought of already and also why i think this won't work:

Taking apart the magazine: won't work because the mag screw doesn't have enough space to come out and the the 2 plates also don't have space to separate.

Ramming the rounds further down the barrel and then later pushing them out after i remove the magazine: this doesn't work because the magazine is like i said empty, wich means that the follower is blocking the bolt from going all the way through, and no I can't wind up the mag because the back plate of the gun blocks it.

Disassembling the gun: like i said I can't disassemble the gun because it is filled with a little under 3000PSI, so taking it apart will like cause it to explode and cause me to get a trip to the ER because of the now frag grenade that blew up in my face.

If any of you have any Ideas that won't cause me to die please let me know.

(Edit notes: So u fixed it, I don't know how wich makes it worse but i started turning some screws and doing some stuff then i pulled the bolt back and then te mag just fell out, I don't know how i did it but i did)

Just mounted brand new Arken SH4J on my FX M3. Went to the range to sight in and had to make 8 minute windage correction just to get on target at 50 yards. Can my M3 rail be that far off?

Should I even bother to try this 1:38 liner with hybrids or return it to the dealer?
I can’t seem to find a 1:22 700 anywhere. Utah tells me FX no longer produces them. I thought I’d found one but turns out when it showed up it was a 1:38.
I’ve not read anything good about hybrid in 1:40 so I’m assuming that they won’t work in 1:38 either.

Looking for a suppressor to purchase that will be compatible with a Hatsan Velox PCP pistol. Male barrel threads.
Can someone point me in the right direction.

Hi, I’m trying to reach naiad001 to get a triple mag holder printed for the mk3 wildcat in 25 cal. My email is [email protected].

Hi
Does anybody know what is the barrel twist rate for the Western Sidewinder in .30 cal?
Than you.

I am going to order my first PCP tomorrow. JTS aircuda max. I would like to hear your feedback on these stores
Utah Airgun
Pyramid Air
Air guns of Arizona

I’m new and this is my first post
I have been shooting a Crosman trail np for 13 years. Health issues I can no longer cock the rifle thus the need for PCP
Thanks

I have a ataman m2r bullpup .25 it still fires when the safety is on. Please help the manual that came with the rifle shows a diagram with screws to adjust. The problem is they’re not in the same places as the diagram.

Hi everyone I just ordered a Taipan Vet 2 700mm .22 from Talon tunes and should be getting it this thursday. I’m very Very exited. There is one thing though. I am new to PCP rifles AND have only had gamo .177 rifles and mostly shot walmart crossman premieres which they shot really good IMO. i don’t know much about ballistics or anything like that(also have never used slugs). What do you guys recommend me getting? Ive read that JSB redesigned work fairly well but theres 3 options. Shallow regular and deep skirt. I will shoot the pellets anywhere from 30yds-150 and will be mainly dove hunting.. What do you guys recommend getting to test out? It would be even better if somebody with a Taipan vet 2 with same barrel length chimed in. Thanks in advance.