yup..... one more question amigos.... What happens when you need to storage your fx dynamic double express and you have to take that air out of your bottles? What's the recomendad pressure to leave on the bottles? I heard you only need to bleed the one in the back. Is that true?
Thanks a lot for your always support here! Super thankful always. Saludos!!

I'm see videos about cleaning and lubing pellets and am wondering if you should also perhaps clean big bore slugs? Anyone have any info about this? I cannot find any threads about it. Thanks...

Somebody please help! Im shooting 25.39 diabolo pellets... this rifles shoots better at 80 on the regulator. BUT uses a lot more air from the bottles ? WHY? isn't it supposed to use less with the regulator at a low pressure? At 80 shoots with a lot of power. Tried at 118 yesterday and its a joke. Why does that happen?
Really appreciate your help!!!
Have a good one there! Saludos

Howzit guys hope you all well

So I recently bought a HATSAN Factor Sniper L .22cal
Iv been searching high and low for the optimum hammer settings , Reg Pressure and slug grain to use but I’ve failed
could someone please help

When the gauge on my cs4 compressor reads 4350 psi the gauge on my avenge x reads around 3950 psi.
Is there a way to find out which one is correct?

Hello, I'm new to the air gun world and recently purchased a Red WolfHi power in .177. I'm shooting the 16.2gr Beasts and they were shooting around 940-965 fps. Accuracy was realistically 1/2" at 25 yds, not good. I took it to AOA and had them do a retune on it. They throttled the hi power setting down to push that pellet between 885-913, and accuracy is a better but not where I think it should be shooting. My question is this. I'm seeing a velocity spread of about 28fps. Now, a little about my background, I build long range hunting rifles. I spend hours and hours tuning guns and developing loads. You can't get consistent accuracy without velocity consistency. With the loads I develop for the guns, I strive to reach a 10fps max spread and by doing that usually makes the rifle a sub 1/2 moa gun. Can anyone tell me what kind of velocity spreads I should be getting with this Red Wolf? Hunting rifles or air guns, they all have barrel harmonics and if the projectile does not exit the barrel at the same time every shot, you can chase your tail forever. I use tuner brakes on some of my rifles and most of the time they work. I installed one on my red wolf and it helped considerably, basically by minimizing the barrel movement. It would be much better with velocity consistency. I feel I should be able to shoot 10 shots at 25 yds and clean the X ring outta there in perfect, indoor conditions. Is the realistic? Any help would be greatly appreciated. I'd like to shoot Benchrest with this gun but its not there yet.

soon I will be competin in 25 and 50 mt benchrest with my unregulated Benjamin marauder in .22 cal, Ive found that it really likes de .217 18,13gr jsb pellets, so now i need to figure out a tune in which ill get just the right ammount of speed and as many shots as i can get from one fill.

So I own a daisy 131 air rifle and I want to put a scope on it but it has one of those old fashioned rails I don't know what it's called though I've been hearing dovetail rails Weaver rails and the more famously known picatinny rails sorry for the terrible spelling but I don't want to order the wrong scope and not have it fit and if someone has a good recommendation for a decent price for a scope please let me know

I Have an early S&W mod. 78 G made by S&W in the early '70's , it's in near new condition but the seals are shot and I'm looking for advice on who I might send it to to have it resealed and checked out.
Any and all suggestions are appreciated.
Thanks a bunch, Moe M.

I would like my 52 .25 to not be so top heavy. I have a RWS riser stop 20+ or 17.1+ only because of the hangover stop. Not for droop.
I want to get the scope low but I don’t know about just rings on those.

A custom lefty would be nice also for it & a HW90 .25.
Not show piece, a utilitarian build. I think I’m going to sell a few to fund some upgrades.

Hi everyone me again. I just want to know if you can fill your gun with those compressors made for filling the scuba bottles. I saw a video made by Patriot outdoors saying they are not made to fill the rifle but the scuba bottles. If I buy one of those I can use it to fill my rifle and later on buy a bottle and fill that aswell

I'm not sure if anyone else experienced this. Had the King now for a few months and noticed a pretty big extreme spread and POI change. I keep my settings the same and clean the barrel when needed so I dug deeper. Looks like the hammer chamber in the block is getting debris possibly from the pellet probe assembly and getting jammed up with the hammer. When I took out the trigger, there was aluminum debris all over it. I took a few pics with my bore scope.

I`ve had my marauder for about two years now, mostly shoot for hunting, but in a few weeks i have my firstr competition, I dont have a lot of information about it other than it is two categories (25 and 50 mt) and I registered for both, my marauder is not regulated, so i plan to use it for 25mt, a friend offered to lend me his Air Venturi avenger (wich due to the regulator i plan to use for 50mt), i plan to shoot 18,13gr jsb pellets from my rifle, and out of the avenger.
can anyone suggest a speed/tune for the marauder and the avenger?
keep in mind that i can only fill both rifles at 3000psi since thats what my air tank is rated for.

I have a new Stoeger s8000 E Tac in .22. I like the gun but not the trigger. I contacted GRT but they didn't know what would fit. Does anyone have a suggestion to lighten the trigger pull? Thanks for your help!
Will

I just purchased a new Diana 54 Airking Pro (laminated stock) in .22 cal. I was siting it in and found that the first shot would be dead on, the second 3" low, the third dead on (same hole as the first) and fourth 3" low (same hole as the second). I was very puzzled until I realized that the entire action slides within the stock and it was not returning to the front position when re-cocked. So, I manually pull the barrel forward within the stock after every shot and it's always dead on.

The manual says that it should automatically go back to the front position when re-cocked. Any ideas?

Also, the entire mechanisms shifts within the stock (see pics). Is this normal? Pyramid Air (Seller) said this is a defective gun but I think they might be wrong? They said that the there should be no movement within the stock. However, I thought that's what a sliding action did.
Any help would be immensely appreciated.
Dan

Question ?? I'd like to check/replace the O-rings under a new regulator. How do you get the belleville washers out so you can check the O-rings. Don't want to force them out (unless necessary), & do damage. I'm a newbie.

and you had no other way of charging your pcps other than a hand pump, what springer would you choose and why that one? Just a thought!

I am trying to find some links to an external inline regulator for tethering my air Force Texan 457. Thanks in advance!

I do not have questions but wanted to post and update and thank everyone for all of the helpful and very appreciated advice about my Dragon Claw not shooting straight. I cleaned the barrel and it was super dirty!! I watch A LOT OF videos on how to properly mount a scope, took the scope of, leveled gun and mounts and used a plum bob to align the scope reticle plumb with the gun being level! I cleaned, and lubed my pellets. After getting everything right and getting close at 25 yds I moved out to 50 and definitely got it sighted in and definitely getting good groups. I was actually shocked that with a 330 gr slug it shot so great!!!! Thanks again for everyone advice. (PHOTOS ATTACHED) White target 25yds, splatter target 55yds!!

Who knows which 2-stage triggergroup can be mounted on a W.A.R-Flex? Maybe a Marauder gen 1 or which one?
All answers are welcome.
Thanks a lot of

I didn't think it would be that hard to replace. The part number is 11505. It is 1 inch diameter. PYRAMID AIR doesn't have any. But I will buy any compatible gauge.
Any help finding one would be appreciated. John

Does anyone use their Rock Chucker for a press. I noticed Corbin doesn't offer the dies anymore. Any alternatives.

I was given a Crosman 760, photos attached. I’m trying to find the year of it (I can see 818037 in very small font on the upper left side of the trigger assembly), and need to order parts for it - once I know which year it is!). Also got it partially dissembled but can’t see how the spring shown loose in the photo should go back in - I assume it should hold the pall into the firing mechanism until it is released by the trigger. Also, what holds the safety “piston” in place in front of the trigger - have I lost something?? Any help would be much appreciated!

Bought a tuned hw77k, I was going to buy a pro sport but it's too expensive for what it is. As uk air rifles are limited to 12ft/lb.

Hi guys new to the airgun world , is there any suggested tunes for a fx impact mk3 ( stock) for me to run the baracuda 21.15g pellets please
Kind Regards Pete