Hello there! I have an almost a month old FX Dreamline Saber Tactical Elite Model of .22 caliber. Out of the box, the Settings were 120Bar/Medium/17 (Regulator/Front Adjuster/Hammer Tension). I am using only 15gr and 18gr pellets and i think i am already on maxout of my settings and they are still below the 910fps recommended. Could you please see if i have to touch the regulator pressure now but on videos on youtubes some are already having even below 120bar Reg pressure but getting higher velocities.

Here are my Chrono Results adjusting only the Hammer for now:

@15.89gr JSB Hades
120Bar/Medium/17
823fps or 251mps

@15.89gr JSB Hades
120Bar/Medium/21
880fps or 268mps

@15.89gr JSB Hades
120Bar/Medium/23
900fps or 274mps


using heavier grain:

@18.13gr HN Baracuda
120Bar/Medium/17
816fps or 249mps

@18.13gr HN Baracuda
120Bar/Medium/23
850fps or 259mps

Can anyone recommend a safe and effective cleaner to remove corrosion from the aluminum threads and fitting in high pressure air tanks? Any tips and tricks so I don't ruin my expensive airguns would be greatly appreciated. Thank you!

Good afternoon,
I have a Air Venturi Avenger which was my 1st PCP. I have had a lot of fun with this rifle but it has developed a small leak. Using the soapy water trick I found that the leak is at the degassing valve. I degassed the gun and took the needle out of the port to look for anything that might be causing the leak. The port was clean. I then recharged the gun and still have the leak.

The gun is over 1 year old so it’s out of warranty. Any suggestions will be much appreciated!

Hi I was shooting the wildcat today, 2 weeks old, and after my second magazine I felt air flowing past my ear, so immediately stopped shooting and asked my friend if he also had this with his crown. Well nothing like that on the crown, you can see what I mean in the attached video.


Has anyone got an idea what might be wrong?

Thx in advance and have a great weekend..

I owed an Impact M3 and was pretty impressed with its capability to shoot slug accurately. But when it comes to holding zero day in day out, my M3 does do a good job and it's a bumper trying to rezero my gun any shooting session. Just few clicks like 5 to 7 ckicks but I don't like the idea of zeroing every time I go hunting.

Has anyone with a slug shooting RTI prophet (either 1 or 2) can confirm if your gun could hold zero time after time? I'm shooting 27gr to 30gr .22 at 950fps or 33-35gr .25 @950fps that's all I need.

Thanks a bunch!

I have two pump pistols and the instructions of each say leave at least one pump before storage. Now I have just purchased a Crosman 140 and feel I should pump it at least once prior to placing it in the closet. What is recommended for the 140? Should it have some air in it before storage?

Hello, I am new to this forum and this is my first post. I am looking for some to make me a mold to Cast and Swedge .30 cal pellets. If anyone can connect me with a person with this ability I would be very grateful.

I bought the 600 way back in 1963. It has been sitting in the box unused for a majority of those years. I recently decided to take it out of the safe and see if it was still operational. I inserted a Co2 cartridge and capped it and when I pierced the cartridge, the gas immediately leaked out, which was not unexpected. I found detailed disassembly instructions on the internet and ordered a seal kit from Ebay. I do small modifications and repairs to my cartridge and muzzleloading firearms so I decided to replace the seals in the 600. Thanks to the instructions all went well until I had to remove retainer pins that hold the rear valve in the inner tube. I threaded a 6 x 32 screw into the first retainer and it came out as described in the instructions. I threaded the screw into the second retainer and became very unhappy when the screw twisted/broke with the pin still firmly in place. I'm looking for suggestions on how to handle this dilemma. I am ready to send the part out for repair should that become necessary.

Does anyone have an update or even ballpark estimate for when the Umarex Primal shotgun that was exhibited at Shotshow 22 will be available??

what is the best pellet for this gun from the pellets mentioned from below?Any ideas?

GAMO Cal.177 Match Pellets​

GAMO Cal.177 Magnum Pellets​

Cal.177 Hollow Point Slug​

Hello guys,im kinda new to pcp world and got myself an entry level airgun...gamo arrow .22, after searching for information found out that regulator's are big deal...and saw that models like gamo coyote are possible to tune and install regulator, but didn't find any information yet about Gamo Arrow, anyone can help me out with this ?
Since is a cheap pcp I believe many ppl own one and this might be helpful for a bunch of guys, the airgun is nicely accurate to about 25yadrs and I believe that regulated it can be pushed to maybe 50.
Thanks.

I'm about ready to "pull the trigger" on a new rifle and would love some input from the fine members here. I have never owned a PCP before, so I'm pretty clueless on what to expect.
I'm looking at:

JTS Airacuda Max in .22 & JTS COMP1 Portable PCP Compressor​

I have watched several YT vids, and all seem pretty positive. As this is my first outing with PCP, I can't blow huge money just yet.

Advice on what gr. pellet would perform best in this rifle would be of great help as well. I tend to stick with H&N and JSB in my other rifles...
I will use the gun for backyard plinking mainly, but with a rodent/bird kill occasionally.....75yrd

I was delighted to find out JTS (America) is located just 30 min from my house, so if any issues arise, then pounding on a door shouldn't take that long.

Any thoughts or suggestions would be most appreciated.

Is a gun with a wood or polymer stock better?

What is more important, FPE or larger caliber? I have a 30 caliber putting out 40 FPE. Also have a .25 caliber doing 49 FPE. Larger caliber creates wider wound channel but smaller caliber travels much faster and hits harder. I'm thinking the .25 would be better over all but I could be wrong.

I just purchased a Hatsan Blitz
I seen macabespeed had a video showing his modified hatsan blitz that he turned into a mini.
Can anyone steer me in the correct direct where to purchase a smaller shorter barrel and a folding butt stock that are both compatible to the hatsan blitz?

---

I am looking for a suitable airrifle for hunting/target practice.I have found 3 guns within my budget.

I new to air rifles so I do not have quite the knowledge to distinguish which is a better option for me.
Can anyone give me a clear explanation on what is the best option?Pros and Cons?Reliabiltiy and Consitency.

What do we need to do to service air rifles?

Here are the guns-Artemis SR1000S
Hatsan Striker 1000S
B3-P air rifle

Scopes are included btw

How do you increase the velocity on an fx impact
Thanks for the help

For 74 year old eyes? Benchrest, not hunting.

I'm considering AEA aka BinTac airguns with the 250cc aluminum tanks (e.g. S45 single tank version) but I'm concerned about running 4,500 PSI (website typo?) in a metal tank. As you know, carbon fiber is rated for 4,500 PSI but aluminum is limited to 3,000 PSI, generically.

Can some aluminum tanks compensate with greater wall thickness or alloys? I like the streamlined look & size of aluminum vs. CF bottles on those guns. Not seeking maximum shot capacity, just compactness and quicker fills.

Another aspect is that CF tanks are said to be more fragile in terms of outside pressure, e.g. the Titanic sub implosion (they say CF handles far more pressure inside). I want a tank with less risk if something hits it accidentally.

Thanks for any details.

hello everyone! I have a question for all you seasoned pcp vets out there. im new to this, ive been a springer guy for years but just recently got my first pcp air rifle. I have my akela tuned with the hammer spring already being cut down, right now im running the 10.34 hades pellets at 905 fps (great stability, accuracy and power) I noticed the other day when the temp dropped that the fps also drops, makes sense so far...but today, the temp is 49F, and I saw that if I shoot my gun rapidly the gun hardly pushes any air at all. like pellets stuck in the barrel type of thing. if I shoot slowly, it seems to be fine. has anyone else had this problem? I did some quick research and it seems that manufacturers say the cold won't have much impact but im curious to hear some real world experiences. I live in Michigan so it's winter for like 6 months a year these days, so not being able to shoot my pcp would not be ideal. any thoughts?

Hello all!! is anyone local to northwest Georgia that does any hunting or target shooting!?

I recently moved to Virginia. I want to get my son into squirrel and rabbit hunting but he hasn’t had much contact with actual guns so I looked into air rifle hunting. However when I look up Virginia regulations the only thing I can find is that it has to be over 35 cal for deer hunting. Any additional information regarding small game in Virginia would help.

Is it possible and how can it be done. Would just like to have a option to do so

and you are trying to see if they had any history? beside,s going down to the post office and check the Bullant board?thanks again Willy

I'm a newcomer here but need a bit of advise. I bought a Crosman 140 (I don't know what varient nor do I know how to tell) but it needs to be resealed. I cannto get the brass piece off of the pump rod I've cut down a washer and tried that to no avail. I've tried a screwdriver which was no benefit. I absolutely cannot get hat brass iece off and it is worth mentioning that based on plier marks on the aluminum parts of the air gun that it has been worked on before by someone who obviously didn't know what thtey were doing.
My only alternative at this point is to buy some Liquid Wrench and soak the end of the rod with the brass piece and see if that will loosen it or buy a replacement pump rod with a new pump cup installed. So my questions are:
(1) Anyone with otehr ideas to remove the brass peice holding on the pump cup and
(2) Is there a source where I might purchase a rebuilt 140 pump rod with the pump cup already installed?

Many thanks!