Are there any air gunners in the Aiken SC area, looking for someone in the area to shoot with.

I'm having an issue getting any pressure and I think it's my quick disconnect. It's just a straight hole. Is it supposed to look like that? I think it's missing something.

I’m new to this air soft stuff so far it’s great let’s just call me dumb. So I just put a new co2 cart into my pistol shot a clip and took the co2 out is it ok to release co2 in the house? I opened the windows and will it break my gun. I know I wasted a cart I just wanted to test the gun before I actually decide to go use it on a field. Also I have a minor headache now

Hello, I registered here some time ago and so far I have really enjoyed reading the great posts.
Because I'm not yet allowed to post in the classifieds thread, I'll write this here and hope that I haven't done anything
wrong in this forum.
I have a Leshiy 2 in .177 caliber. I am extremely happy with her. I come from good old Germany ;-).

Mod edited content: does anyone know where I might find a spare .177 magazine?

Please don't be angry if I'm in the wrong thread with my post, unfortunately I don't know my way around here very well.
Thank you and I wish you a nice week.

If the diameter is too tight. For instance .219 versus . 217. What effect do loose vs tight. Less spin more spin. Etc. Bob

I was changing out the stock on my FX Crown and while removing the power wheel, I lost the 2 tiny detent ball bearings. Anyone know where I can find replacements? I tried my local hardware store but they did not having anything that small. Any help is much appreciated!

I am considering a carbon sleeve for my .22 FX Crown lightweight standard barrel . Can anyone provide some feedback on their results as far as accuracy improvement if any . Also Is it best epoxy it to sleeve? Thanks in advance.

What kind of coolant fluid and oil should I use with the Alpha Carette 4500 psi Air compressor?

Thanks

Dennis say's "intended to be used with the cast lead .45ACP bullets" on his web site.
Looking for any real world experience with purchased ammo (not cast at home but hey please add that if you have it) weight , getting place , what Not to try ... .
I assured a friend someone here would have good info so please proffer some experiences good bad otherwise.

Thank you,
John

I have a .25 avenger , an Arken scope , Donny fl tanto.
Reg set at 2300-2400 ish. Hammer spring backed all the way off. Shooting JSB Hade 26.54 gr and Jsb king .25 25.39 gr.
At 20yds out 60 yds groups are almost a ragged hole or at least touching. At 100 groups start to open up really bad.
Any help would be greatly appreciated. Thanks

i have fitted a lane airbottle regulator,can somebody explain the filling process with any advice as im not getting the procedure correct

I am looking for a shop that has 3 lt tank and valve for charging air guns. Went through all the usual sources. Pyramid air, Utah airguns, high pressure pneumatic, Air tanks for sale, AoA, etc.
I really don’t want to buy from Amazon, rather support an airgun shop.
I see some 100 cu in ones which are a little too small then jumps right to 74-100 cubic feet . Nothing in between.
I want to use my Hill compressor without putting too much load on it for each charge.
3 liters seems to be a good amount for enough charges for 3-6 card competition.

My jet 1 is leaking air from the barrel. It has been filled 5 times.

Hi...Just received Donny Ronin and adapter for .22 RAW HM1000X. Problem is that I do not know how to remove cone shaped moderator mount. I have hardhat a lot of heat is required. Question(s)...Is the cone shaped piece a screw on or press fit? Is there a tool recommend to remove it. IE: channel locks or other round object wrench or do you apply linear force by tapping on mount to break it loose. Thanks for your response...En4cr

Hello everyone, I have a friend who just recently purchased a Ruger Air Magnum in .22 and he needs a scope badly, as his eyes aren't as young as they used to be. Any ideas? recommendations? or insight? Thank you, god bless!

Hello everyone,
Does anyone have the measurements of a 0.22 217 slug mold or a slug I'm new to this, I want to make a slug,
Thank you, Have a nice day

Been looking at these two PCP air rifle and I’m trying to figure out what is the difference between the two of them

Looking for advice on a scope for a aircuda .22 for squirrel hunting . Price about 150 to 200. Any help would be appreciated, new to the air pcp rifle shooting, thought this would be a good starter piece.

I heard you can increase the performance on the dragon claw dual airbow. Who will do this for me?

I heard you can increase the performance on the dragon claw dual airbow. Who will do this for me?

I am currently looking for AIR GUN ACTIVITIES; I shoot for my mental therapy at my home range ( I have 70ft of shooting space ). I shoot when my mind gets overwhelmed when doing school, and in between hard assignments, I target shoot; this sharpens my focus. Then I go back and do a little more and then shoot again; by the time I get through half a tin, I have either finished or retained any concept I was studying.

But now I want to step up; I want to pest hunt, but I don't have the pest to shoot. I want to do a competition, and I have already missed one in Palmer, Ma ( it was on mothers Day. The misses would of whoop my a**). So before I get a job, I would like to join a gathering and have fun shooting and socializing. At this moment I have been going to AIRSOFT, such an exciting sport.

How can I find planned future events in MA and maybe as far north as New Hampshire and as south as Warwick, Rhode Island? I am also willing to go for pesting. So far, I have discovered one possible place in Connecticut, and NAG outside range will be opening soon, and I also need to buy a new rifle if I want to do this. The beautiful thing about Massachusetts is these trips are a top 2 hr drive. I am willing to make plans; thanks y, all.

I’m new to PCP rifles and new to this community. I’ve always wanted to get into PCP rifles but they were cost prohibitive. I recently found a Gauntlet Gen 1 .25 on sale for $200 and couldn't resist.

I decided to tinker with this, and upgraded the bottle to a 0.38L and a 2200 psi reg (was 1900psi reg). When I put the new reg on, I lost an average of 56 FPS (Shooting 850’s with the 2200psi reg and 900’s with the 1900psi reg). I checked the pressure on both regulators, and they’re both surprising spot on (1900psi reg putting out 1900psi, and 2200psi reg putting out 2200psi).

Does anyone know why I’m increasing pressure and loosing FPS?

I’ve only shot Javelin Slugs out of my Wildcat in .217 diameter but have been wanting to try some other options as well. I’ve shot 30gn/950fps and done well (30 groundhogs last season), and this year I switched to 26gn/997fps to flatten my trajectory a bit. I do have the slug power kit installed, and the stock Superior barrel.

More curious about different diameters than anything else. I bought .217 because that’s what the shop said generally shoots well. Will I notice a huge difference going down to a .2165 or up to a .218?

Hoping someone else has already done the testing and can save me the money in slugs lol.

Thanks

I have a caiman in 25 cal. Bought it new from Utah Airguns. I'm a little puzzled....

It came charged to 250 bar. I fired it a little and when it hit 200 bar I charged it back with a Hill Hand Pump.

I took it out of the case a day later and it has ZERO air in it. Totally flat............

IS that a normal experience? I've only charged it one time. Any thoughts?

hello I just bought a used 25. cal FX crown . My main intended use is punching paper at 50 yards with pellets . To those of you who have both 25. and 22. cal ,which do you find to give the best match grade accuracy ?