Air Arms Utah Airguns Pyramyd FX Airguns Daystate Airmaks Airguns Diana Airgun Depot Edgun West Palm Beach Airguns DonnyFL
Saber Tactical Optisan Side-Shot Scope Cam NE Airguns Baker Airguns AGS Topgun Airguns Predator International The Pellet Shop Huben Airguns Huma-Air Shooting Supplies Hurricane Luftvapen AEA Precision Airguns H&N Impulse Air ZAN Projectiles Hawke Optics Kraford and Lypt Airforce Protect Your Nuts Stud Mag Loader RX Target Systems Sports Match Scope Mount Specialists Altaros Slugs Banner CTA Thomas Air Performance Air Rifles Hatsan USA Georgia Air Guns SPAW Minor Skout Airguns RAW - Rapid Air Works Nielsen Specialty Ammo Patch Worm Weihrauch Sport Talon Tunes Airgun-Revisions JTS PARD ST7 PPP RTI

Just tried AEA, 66gr pellets in my Boss

Yeah Dave, .30 cal. Such a great shooting gun. The Huma HP reg I installed last summer (set at 160 bar) has been amazing. I couldn't shoot Hades in it before with the OEM reg even though they're the same weight as the 44.75 diabolos. Just not enough oomph. NOW it's pushing 66 grains with MOSH (minute of squirrel head) @ 50 yards! Next time out I'll see what it does at 75 & 100 & how much holdover is needed.
Cool. You should be about 725 fps with 77 fpe. Should be good at 50 yards, but drop at 100 will be much more than the .30 pellets you normally shoot. About 7 inches more holdover than you currently use. About 2 Mil.
  • Like
Reactions: Gerry52

Huben  GK1 took out 3

Oh my, spirits too? We may need an exorcist! Or maybe it was too much baby food cooked in aluminium pots. It is dangerous you know? Perhaps the country of Kalifornia has declared those terrible pots and pans to cause reproductive health. Lord knows it has messed up the minds of their government. Next it will be hazardous to shoot air guns. But wait, it already is! We are certainly dooooomed as airgun enthusiasts. Dito.

I gave up hope when I learned the California surgeon General informed me the split shot sinkers I've been biting onto leaders since age 5 were known to cause cancer. Permanently in the moment... It's been 34years...any minute now.
  • Like
Reactions: Bandito

EDgun  Edgun Leshiy 2 .22

I have the Edgun Leshiy 2 in .22, finding a 22 caliber magazines is nearly impossible. I purchased one that is 5.5s, for slugs. Do I need to do anything to the gun to shoot slugs through it?
Nope - just choose the slugs that fit the mag. If they’re like my .30 slug mags (.300), they will shoot .220 slugs. Take a look at thepelletshop.com.
  • Like
Reactions: Cryptid

N/A  anyone have leads on US vendors carrying huggett snipe?

I’ll keep an eye out. I’m looking for a little atom myself. Kick in the ol nuts atoms are only like $70 in the UK. Someone posted a bunch of huggets in one of the classifieds a month or so ago. They had quite a few brand new ones. I think it was on American Airguns. That place with a bunch of scammers

Good luck on your search
Rob

N/A  Which .177 carbine is the best choice

Yes, Weihrauch... Air Arms etc... all were meant for sub 12 fpe. They indeed shoot amazingly well at those power levels. I watched Teds video on the full-length rifle, and it was spiraling like crazy at 100 yards. Is it easy to adjust the power for the HW100?

-Matt
Yes, it's relatively easy. The hammer spring adjustment is easily accessed from the rear by removing the rear plate. The reg set point is adjusted by separating the two receiver modules and turning the large adjustment screw. As with most regulators, the adjustment is sensitive. I believe I turned it about a half revolution. I suggest small increments, maybe a quarter turn and then see where you stand in your tuning balance. It's not as easy as some of the externally adjustable rifles, but it's something you may do only one time. You might hear suggestions to do it all with the HST. That might be possible, but if going from 20 fpe to sub-12 level with only hammer adjustment, you will end up with a very unbalanced tune, which would probably affect shot count, consistency, sound, etc. Better to do it properly once and be done with it.

#1 Pay it forward for Christmas...

I can get on board too if needed, i have a original AGT fill station that came with my Vulcan 3, all it have ever done is collect dust in my window sill.
It is a very basic kit, but will do the job just fine.

NO probe of course that followed my Vulcan 3 to Finland

AGTFK.jpg


If anyone need something like that to make up a complete package shoot me a PM and i will get it under way.
  • Like
Reactions: Rondo

Bench rest target in ft position

Thanks I’m on it

Prophet2 Great results with FX Liners

Hello
my friend got very good results with tuned prophet2 in 75 meter benchrest competition.
Liner 1.16 twist 800mm
34GR custom slug
speed 295 m/s
First place in the competition with 248/249 score in 75 meter!

View attachment 506466

View attachment 506467

View attachment 506468

View attachment 506469

View attachment 506470

Very nice!!!
  • Like
Reactions: mkz

FX  FX maverick mods / ideas

My simple bipod extension might not be worth mentioning compared to the innovative stuff you have done, but here it is. A lot of times my maverick goes hunting or target shooting in wooded or rocky areas where the bipod isn't used as a support. Instead, the extension tube rests on tree branches or logs or rock ledges or fence posts, etc. when taking a shot. It protects the bottle tank and barrel from underneath too. I call it a bash bar.

View attachment 506493

stovepipe
That's exactly what i want to see. I know there are plenty of good mods around this forum from posts that i have seen here but there isn't actually one place where i can find them nor a thread/forum that i know of. Thanks for the reply. It's those kind of simple ideas that just make whatever you want to do work that i seek.

Just installed extra high power huma regulator on my fx impact m4 - NO PRESSURE ON REG SIDE OF GUN

Hey fellas, I just installed my hum air regulator last night for an fx impact m4 and I can't seem to get pressure on the regulator side of rifle just yet.... Any opinions or thoughts would be appreciated.
I had a similar issue with a new human reg on filling VERY slow set at at 170 bar. I contacted Huma-Air and found out that there had been a revision on the number of Belleville washers that are installed for that regulator (1155). Mine came with nine and the instructions showed to use all nine. Huma-Air later revised that to 8 washers and I tried it and it now it works perfectly. I think they had switched to a thicker Belleville washer so only eight would fit to work correctly and I was trying to use nine per the old instructions that came with it using the thicker washers.

Filter