Just wanted to share some information that I saw.

Thanks
Mark

This listing has been renewed

This listing has been renewed

ah... good to know, because I'll be putting a ton of 45 and 556 downrange on them as well as airguns. Guess I'll stick to cardboard.

This listing has been renewed

This listing has been renewed

This listing has been renewed

SELLING TOTAL OF 4 AIRFORCE CONDOR HAMMER WEIGHTS ONE IS STOCK OTHER 3 FROM PCP TUNES
THE WEIGHTS ARE 66 GRAMS , 82 GRAMS 88 GRAMS 10 GRAMS SOLD as a set
$80 SHIPPED Paypal F&F

This listing has been renewed

I'll see your revision and raise you a revision.
For the AW/DW tuning, I've started doing it backwards. I find a tune I like using the advanced settings, then I create a new factory table with the tuner for that barrel and pellet weight and plug in those settings. For example, for shooting JSB 13.43 from a 17" barrel I added a row for 120 reg pressure, 2825 pulse and 75.5 volt for 815 fps. Then I added the row that has my actual tune: 120 reg, 2850 pulse, 77 volt for 820 fps. Then when I shoot I use the factory setting that I created and it's good to go.
I shot for about 6 months just using the advanced setting and it was fine, but with the spring weather and some out of state shoots coming up I think the custom factory tune is the way to go.

This listing has been renewed

FX stackable moderator .22 caliber. 1/2 x 20 thread. Muzzle exit is .290 so you may be able to use it on a .25 cal, depending on your shroud alignment. This is the first generation stackable moderator. Barrel end, muzzle end and four mid sections. Each section is a baffle, unlike the tube moderator offered now. Can be tailored to your taste depending on the length/sound you are looking for. Excellent condition. Same diameter as your typical FX shroud. See pictures of the WC MKIII below for reference.
$65 TYD CONUS. PP FF or USPS MO.
Thanks for lookin!

I have a Titan 5-25×56 FFP APR-MOA. It's in like new condition, has a small blemish on the top turret, Pictured. Does not effect the scope. Rings not included. Asking 550 shipped TYD. I'm selling the gun it was on and not going to be using it, so making room for other stuff. I have excellent feedback, so deal with confidence. Open to offers.

We're going to hold our third airgun shoot at Atglen on Sunday, March 3rd from 10am until 1pm (or whenever we feel like leaving really). We will be shooting 25m bench targets and will be split into two classes, springer and PCP. Feel free to shoot both as we will have plenty of time to run multiple relays. The kitchen will be open at the time of the match and we will also have pellets there for sale if anyone needs to stock up some. On top of that there will be prizes for winners of both classes so bring your A game!

Caliber recommendations are .177 - .22 and we'd prefer that the guns be sub 20fpe. If you have your own adjustable chair we strongly encourage you to bring it and use it. If you have any questions or concerns feel free to reach out to me.

Cost: $10.00 gets you as many rounds as we can fit in

Address:
Atglen Sportsmans Club
82 Creek Rd, Christiana, PA 17509

As a final note, the benches have been updated since our first round. The wall has been reinforced which has resulted in a much steadier shooting position!

This listing has been renewed

It's a nice gun but the plenum of the stock gun is quite small. Like 10 or maybe 15ccs. For a 177 it is fine. For a 22 it isn't bad. But the additional plenum really helped my 25. I might put one on my 22. I think the South African one is the biggest and it is only about 35ccs. It does make the gun a little longer, however.

My setup got some updates.
Built cradle and compressor is in it with springs - zero vibration outside of the cradle and it runs way quieter than before.
Added water/oil separator.
For cooling I'm running straight from tap (from my private well, +4 degrees Celsius) cold water. Outgoing cooling water goes down from the drain.

Thanks fellas. Sounds like there is no need to tinker then, thanks for saving me time chasing my own tail. That's why I asked. Wondering if there were any gains in accuracy to be had aside from more energy and more air usage if I upped the FPS.

This listing has been renewed

This listing has been renewed

Aside from the topic shift to coated pellets, what the OP is suggesting basically sounds like the foundation of sabot rounds which have been around for at least 100 years and work quite well.

I have this now for over 6 months with no issues...love the fact it's a 350watt motor also .....the temperature hasn't even gotten to 90° yet!!!!!! It definitely fill a carbon fiber tank....

im looking to buy a BSA super 10 in good condition. if you have one you dont want or use any more let me know. 22 or 177 caliber.

This is the Best Deal on the Planet you'll find for this gun! Won't Last Long - Pristine FX Impact M3 .22 Power Block Sniper - 700mm Superior Barrel w/CF Liner Sleeve.
580cc FX CF Bottle w/ Stainless Best Fittings M3 300 Bar valve, Premium Parts include FX Angled Manometer Regulator Gauge, Huma Air .22/.25 Adjustable Pin Probe, and K&L Ultra Grip Probe Carrier. Also Includes x1 .22cal FX Sideshot High Capacity Magazine, FX "Empty Can" Moderator, FX Impact Hard Case., and a Brand New Tin of JSB 18g pellets. Gun has NO ISSUES or LEAKS!! It's working perfectly Still has a year of full factory warranty. I'll be happy to answer any and all questions, PM for contact Info.
$1500 + actual shipping. No Trades, Serious Inquiries only Please.

Background: This M3 is one of three I own along with a few other guns and it just doesn't get shot. It's a great gun in perfect condition and it's time it found a new home where it will get used as it should. Although not advertised, I can set this gun up in any configuration from Compact to Sniper in any caliber up to .30cal. I do have some very nice accessories available if you're interested. Thanks

BIPOD NOT INCLUDED - Barrel Band IS INCLUDED.

The Krait is one of my favorite shooters!