Diana My 22cal Chaser. You need one!!!!

[oregondude]

Got this from AOA for $75. Can't beat that. At first I could not get it close to zero, maxed out the turrets at ten yards, and was 3 inches high and 4 inches left. Removed the 3D printed moderator and she dialed in. Got a couple of 6 round mags and a aluminum moderator from Wes at Airgun Archery Fun. Two really good products. The moderator is direct fit, m10 x 1 threads. $34. Mags were $20 each. I put in a 8mm bushing (5/16") to pre-load the hammer spring for a bit more power. A nylon bolt of the correct diameter cut to length would work great. After adjusting the trigger, I mounted a 1-8 LPVO Riton . Going to switch to my Hawke Frontier 1-6 LPVO. Gotta love a $750 scope on a $75 pellet gun. Trigger adjustment is super easy . See YouTube. Seat the screw flush, back out 2 full turns. I also adjusted the first stage for no take up. The cheek riser is a block of ridged foam taped to the stock. Kinda ghetto but functional. Accuracy is impressive for a CO2 pistol. Tried 11 pellets and the RWS Super dome and the AEA 18.3 were easily the top 2. AEA WAS THE BEST. As usual. The AEA dead on at 10 yards is low 1/4" at 25yds. I don't shoot squirrels, but if I did, I'd be confident to 40 yds. At 4lbs this is a great walk around hunter. Rabbits at 35yds should be no problem. Head shots, please. I chose the Diana Chaser over the Crosman because of the magazine option. Thanks for looking. Get one, their fun, fun, fun. Cheers , Bill and Addi.

 

[marflow 777]

so, where have you been i have been in the Chaser rabbit hole since 2019
do you have an old or new version
the new version lost the front trigger adjustment screw while it kept the rear one no one knows about and either way both screws are to short and the sear spring can be replaced with a lighter one and the sear can be drill for a trigger stop but i have written about that to many times
duct tape, try one of these
https://www.atioutdoors.com/product/sks-fiberforce-cheekrest/

 

[Nattboy]

I have one. Got it to teach my grandson to shoot. He loves it and so do I. It loves JSB 13.4's. I tweaked it a little. I get about 35 good shots before the power starts to drop. It shoots at steady 625 fps. If memory serves that's a little over 13fpe. There is a fellow in South Africa that has a you tube channel and he has done a series videos on tweaking and trouble shooting these guns. He has helped me out of a few tight spots. I mounted a Hawke 4- 32 AO scope on mine, The weather is getting right to have some fun. Happy Shooting.

 

[oregondude]

so, where have you been i have been in the Chaser rabbit hole since 2019
do you have an old or new version
the new version lost the front trigger adjustment screw while it kept the rear one no one knows about and either way both screws are to short and the sear spring can be replaced with a lighter one and the sear can be drill for a trigger stop but i have written about that to many times
duct tape, try one of these
https://www.atioutdoors.com/product/sks-fiberforce-cheekrest/

View attachment 556461View attachment 556462View attachment 556463View attachment 556465

As referenced in my post, there are 2 trigger screws. I adjusted the first stage to eliminate take-up. Trigger breaks at 14oz. AEA 18.3 pellets shooting 1/4" at 25yds. Not a rabbit hole, just a great shooter.

 

[MJS]

Mine's terrific. Really decent shooter.

 

[oregondude]

I have one. Got it to teach my grandson to shoot. He loves it and so do I. It loves JSB 13.4's. I tweaked it a little. I get about 35 good shots before the power starts to drop. It shoots at steady 625 fps. If memory serves that's a little over 13fpe. There is a fellow in South Africa that has a you tube channel and he has done a series videos on tweaking and trouble shooting these guns. He has helped me out of a few tight spots. I mounted a Hawke 4- 32 AO scope on mine, The weather is getting right to have some fun. Happy Shooting.

That would be 11.6fpe.