Recent content by HogKiller

  1. HogKiller

    Tequila Gun PCP

    I have a wife for that, thanks. /g
  2. HogKiller

    Tequila Gun PCP

    Didn't say that, I've got a red dot and with the Tequilas new adapter it's a perfect alignment to the top of the front sight or the hole, forget which, but it's an annoyance to me. My PBs are a different story, just iron sights on the handguns.....except for the Mark III, slapped a red dot on it.
  3. HogKiller

    Tequila Gun PCP

    Personally, I find the front sight annoying in my line of sight with his new mount, I 'solved' the issue with a piece of black electrical tap, just tape it down, boom problem solved.
  4. HogKiller

    FX Maverick Problem adjust hammer spring

    Ahhhhhhhm, THAT will do it to you every time and no, not stupid just inexperienced.* Personally, I'd still add some lube to the hammer and trigger, you can add the lube from the outside after removing the spring, just a few drops around it, it'll work in. * I f'd my new Tequila gun by trying...
  5. HogKiller

    FX Maverick Problem adjust hammer spring

    You are getting too much air. Ok, then 1. you are getting higher pressure on your #2 than indicated,. #2 you have a messed up spring #3 a heavier hammer or......This is going to be fun, for me not for you but it's not too bad. You're getting more pressure than the spring can handle,. #1 make...
  6. HogKiller

    Tequila Gun PCP

    the Tanto should do the trick, it's light enough and really tames the bark, enough so I can shoot in my back yard and not have the local LEOS roll up in their armor. It does make it long but, oh well. Try each one and see what works.
  7. HogKiller

    FX Maverick Problem adjust hammer spring

    Short answer is, your lack of tune sucks, not to be mean but...we've all been there. First drop your reg pressure down to 110, maybe lower, Screw in your Macro adjuster screw, all the way then back it out 2 turns, turn the dial to #7 and see what it does for 3 shots, drop it down to say #5 it...
  8. HogKiller

    FX Officially an FX owner now.

    Well, there is always getting her a nice bicycle and maybe a trailer to haul the groceries in.
  9. HogKiller

    FX Maverick Problem adjust hammer spring

    The regs have a brass bit and another 'hopefully' brass bit with a Delron insert, going against the Delron will put a divot in it. WHICH it gets just in normal usage. Official kicker, some of the brass/delron bits had the delron too long, almost impossible to get enough pressure out of the...
  10. HogKiller

    FX Maverick Problem adjust hammer spring

    5 turns is 5mm that's a touch much IMHO. The overall measurement only needs to be about 18-19mm, at 21.5 or so it'll mess up the trigger, as it it won't reset.
  11. HogKiller

    FX Officially an FX owner now.

    In all honesty, they are somewhat pointless out to 100, it's more the challenge of getting them to work well. Now if it's windy they are nice to have, that and a lot of luck.
  12. HogKiller

    FX Officially an FX owner now.

    Swapping out the barrel leads to other things, mostly not good unless you get really lucky the first go round. Your gun MIGHT like the 22gr RMR slugs, they are the ones who make the FX slugs, but at that short range it's not worth it.
  13. HogKiller

    FX Officially an FX owner now.

    Ahhhhh, I was wondering how you got a FX that actually worked out of the box, now I know. I've got 2 Mavericks, one is my messing around gun, the other a slightly modified .25 600mm barrel.
  14. HogKiller

    FX Officially an FX owner now.

    You might wish to try some AEA's in it, I and a few others have found they are a touch more accurate. I doubt you'll be shooting them at 100yards so no need to get carried away with slugs. Which is another deep branch of the Rabbit Hole®, which I'm welcoming you to. Hey people he likes to...
  15. HogKiller

    Fishing for compressor advice / knowledge

    Don't assume you'd hear the leak, it took me a while to find mine on my 032. I'd think I heard it when running then nothing. It was the 0-ring on the back side of the right hand filter tower.