Full house actually had 15 shooters two of them doubled up. Conditions were mild and picked up as the cards were shot. Great shooting by Dennis in the Pro Class. Close shooting in Factory also.

N50; Match 1
Pellet:
1) Joe Friedrich, 247-14x, 248-13x, 249-16x, = 744-43x, FX Crown
2) John Voso, 240-9x, 233-4x, 228-1x, = 701- 14x, USFT .177
3) Perry, Perry, 236-7x, 226-4x, 221-2x, 683-13x, Thomas .177
4) Terry Eannetta, 213-1x, 231-6x, 234-7x, = 678-14x, .25 cal Air Venturi

Factory:
1) Dan Burbach, 248-9x, 245-12x, 246-7x, = 739-28x, Bergara
2) Ed Gonzales, 248-13x, 244-9x, 245-15x, = 737-37x, CZ
3) Chris Griffiths, 239-9x, 240-7x, 240-9x, = 719-25x, Tikka

Sportsman:
1) Keith Longerot, 250-12x, 247-12x, 250-14x, 747-38x, Rem-40x
2) Wayne Tsuda, 238-9x, 242-11x, 242-7x, = 722-27x, Annie

Pro:
1) Dennis Kunkel, 250-12x, 250-16x, 250-16x, = 750-48x, Annie

N50, Match 2
Pellet:
1) Perry, Perry, 240-8x, 235-6x, 232-8x, = 707-22x, FX Crown
2) Terry Eannetta, 189, 202, 206-2x, = 597-2x, Air Venturi

Factory:
1) Wayne Tsuda, 238-2x, 242-4x, 241-9x, = 721-15x, Tikka
2) Chris Griffiths, 240-8x, 241-6x, 233-8x, = 714-22x, Tikka
3) John Voso, 230-6x, 235-5x, 237-5x, = 702-16x, CZ

Pro:
1) Keith Longerot, 250-16x, 249-13x, 250-16x, = 749-45x, 2500x
2) Dennis Kunkel, 249-13x, 250-14x, 249-12x, = 748-39x, Annie

USARB, Match 1:
LV:
1) Doug Miller, 247-9x, 244-3x, 245-10x, = 736-22x, Thomas
2) Vipha Miller, 240-7x, 238-4x, 236-4x, = 714-15x, Thomas

HV:
1) Bob Sosky, 249-13x, 248-7x, 247-12x, = 744-32x, Thomas
2) Mark Audette, 238-5x, 239-5x, 245-5x, = 722-15x, USFT
3) Gene Matsupoopa, 241-7x, 195-3x, 239-3x, = 675-13x, Thomas

Match 2:
HV:
1) Doug Miller, 249-15x, 247-7x, 247-10x, = 743-32x, Thomas
2) Bob Sosky, 246-9x, 248-9x, 245-10x, = 739-28x, Thomas
3) Vipha Miller, 241-5x, 246-10x, 247-11x, = 734-26x, Thomas
4) Gene Matsupoopa, 231-4x, 228-1x, 233-4x, = 692-9x, Thomas

Thanks to all that brought the goodies, thank you Tim with help scoring and Perry for you help.

Joe

Where's the cheapest place to get a marauder .25 shroud and barrel and breech plan on converting my marauder .22 to .25 gonna mod the stock .22 valve by taking out the end cap and return spring and putting in a 18lb heavy hammer spring also is a 50 grain noe mold too heavy for a marauder .25??

Out doing some pesting with my impact mk2 today and it stopped firing. Pressure at bottle and reg guages are normal. Hammer cocks and sounds like it drops when trigger is pulled - kind of a click and spring noise. No air us released all mechanical sounds only. Any ideas? I've never had an impact apart, but only because I haven't had to.Thanks.

i had no idea this tripod can make backyard plinking insanely accurate & fun!!!
on the flip side
this tripod can also pointout if ur barrel is poor quality or the ammo u are using is crappy!!!
got it used from Amazon,
few scuffs here and there but nothing that screams return this right now,
so yeah very much like adding this in my setup for sure.

Found this Winchester Model 435 in .177 at a pawnshop today. Missing the front and rear sight but mechanically it’s sound.

This past weekend, Nevada State GP after hours playing around ....
SKOUT .25 cal with the new 35" slug barrel using the Corbin slugs.

My friends rifle, set at @ 2k on HP reg & @ 165 on LP

We were hitting a 18" square plate at 365 yards !!!! and personally did so 2 shots in a row.
This in a swirling wind shooting up canyon into what is very unstable air space.

Earlier on another target before going long while sighting in at @ 135 yards, laid down 5 shots about the size of a nickle

I was Very very impressed to say the least.

201 Shin Sung Fire 9 mm for sale. This is like new. Comes with factory box . If you live near Cleveland Ohio it can be picked up. I shot 115 gr slugs and got 140 FPE . It holds air and has a low and high cocking position. The gun is accurate and can get up to 8 full power shots. I am asking 400.00 dollars plus shipping. I will do PayPal or Venmo.

Diana Air Bug CO2 pistol in .177. Includes 1 magazine and a single shot tray. Less than 200 pellets shot through it. $90.00. Conus only.

GRAPHIC HUNTING FOOTAGE

Umarex Notos squirrel hunt


Check out my new channel! The Notos is perfect for those close to mid range shots. Total squirrel count probably pushing 300.

New in the box Arken SH4 Gen2 4-16x50 FFP MOA scope with new bubble level and throw lever. $275 shipped lower 48. PayPal FF or Apple Pay. If you’re more comfortable with paypal goods and services I will gladly accept, just need to add the 5% fee.

I have 1 like new element helix 4-14x44 FFP MOA scop for sale - Reticle is APR1C. Bought from camera land a few years ago. Mounted on Airguns and never used. $225, shipped Lower 48. comes with sunshade and bikini cover. Sorry no box. Gladly take PayPal goods and services, please add 5% fee. Otherwise PayPal FF or Apple Pay.

2 SOLD , 1 available

Hello everyone, I'm new here and just thought I would share my experience so far with the arakuda max in 22. Been shooting air rifles and have owned several since I was a kid and this is my first PCP.

I ordered the gun from Pyramid Air with the JTS air compressor combo. The first gun I received had serious accuracy issues and I also noticed the regulator was set at 2,200 PSI from the factory, that confused me cuz the manual states that the gun is regulated in 22 at 1800 PSI from the factory, after running across the chronograph and doing my best to adjust the hammer spring I gave up on it ever been acceptably accurate at 25 yards and I just simply returned it and Pyramid Air sent me a replacement, the second gun I received had a crack in the stock right out of the box, again I contacted Pyramid Air they put me in touch with JTS and my first experience in dealing with their customer service was really good, they immediately sent me out a replacement stock. Which I refinished looks much better now!

initially I was pleased with the performance and accuracy of the 2nd gun I recieved, although I did have the issue with the magazines fitting extremely tight marred up the black finish in the breach and on the magazines pretty good until I got that sorted out but then rather quickly I also started to notice that although the regulator was set at 1800 PSI, when I would fill it up to 3200 the regulator would quickly creep up to 2000 PSI. First 10 shots or so would be a bit erratic until it dropped down below 3000 on the main tank and the regulator would drop and hold at 1800. I would get about 15 really accurate shots. Something didn't seem right so again I'm experimenting with hammer spring adjustment but the regulator issue wasn't allowing me to get the consistency I wanted for at least 25 or 30 shots.

I assumed either the regulator was faulty or the seals were leaking a bit. Again I contacted Pyramid Air they told me they could send me a replacement rifle, I was pretty frustrated at this point and convinced another gun would probably just have another problem and I know I should have just returned everything and got my money back. I knew if I tore into the gun and messed around with a regulator I would void the warranty. Being impatient, frustrated and stubborn I made the decision to order a HUMA regulator and swap out the factory one knowing I was going to avoid the warranty on the gun but I was determined to fix it myself... yeah I know I'm an idiot, lol.

I contacted JTS a couple times wanting to get some extra O rings before I tackled this project, I couldn't find anything on their website for OEM parts so I emailed the customer service rep who helped me out with the cracked stock requesting to purchase some extra O-rings and a couple extra piston seals for the compressor...Oh yeah, the Piston seal on the compressor was completely shot after little use, but very easy to replace and they did send an extra one in the kit that I installed but I wanted to have a couple laying around in case this happened again. At this point I could get no response from them, I called Pyramid Air and they gave me a phone number to contact a guy named Travis and I texted him and he responded. I'm not going to go into too much detail about that experience except I will just say that I came to the conclusion rather quickly from that experience that I was on my own now. I went through the schematic of the gun in the manual found the O-ring sizes that I needed went to the O-ring store and ordered what I needed and I'm sure saved a few bucks.

Installation of the aftermarket Huma regulator was very simple although I did have to install a spacer to get the aftermarket regulator to line up like the factory one so the O-rings would be in in their proper position as it sits in the housing.

Got everything back together and I am simply amazed how well this gun performs now. The Huma reg sits firmly at 1800 psi, no creep. And where I was getting if I was lucky 20 accurate shots with the factory regulator being all squirrely I'm now getting 40 to 45 shots @ 870/875 FPS before the Gun starts to drop off the regulator and I have to top it off again. At 25 yards it's damn near hole in hole shots 99% of the time. I'm easily shooting dime-sized groups at 50 yards with jsb18.13.

All that said, I understand it's a entry-level budget PCP and the factory regulators and overall quality control is going to be hit and miss unfortunately, but I managed to get it shooting performing and exceeding my expectations after replacing the regulator, polishing the barrel, smoothing and adjusting the trigger and I learned a heck of a lot.

In my opinion I would stay clear of the compressor... didn't know much about them but after having to already replace the Piston seal on this one and looking at similar ones on Amazon and eBay it kind of looks like they're all the same just package a little different with little gimmick here and there to say one is better than the other, I'm pretty sure the ones that sell for under $300 on Amazon are almost identical and probably made in the same Factory as the $600 JTS branded one... I'm not saying that's the case for sure I have no idea but if I was a betting man

Keep in mind if you pull the trigger on this gun that from my experience and in my opinion it's going to be a little bit of a roll of the dice when it comes to the quality, I probably will not be purchasing any more JTS products anytime soon and I sincerely hope the quality control gets a little better and they have continued success in the future. I'm sure people have gotten them right out of the box with zero issues and have been happy I just was a bit unlucky in that regard, and admittedly my expectations were probably a bit too high for a PCP in this price point. All that said it's a damn good looking gun very fun to shoot, and easy to work on if you have to tackle any issues yourself.

Oh and I did slap on a suppressor and it doesn't clip at all gun is extremely quiet aside from that horrible spring twang thanks for reading the book I just wrote Guys, I look forward to sharing and learning here.

So I have a new gun. Covered under warranty for 5 years. The piston seal is bad. I talked to the rep, and they agree the piston seal is the problem.

Option 1 I get a shipping label, send them the gun, and they replace the seal. I maintain the warranty, but have a seal replaced potentially under the same circumstances that caused me to have a bad seal in the first place.

Option 2, they will honor the warranty, and send me a replacement seal to perform the work myself. I will be able to deburr, grease, and assemble with attention to detail as I see fit...probably eliminating whatever caused the failure in the process. The instant I do that, it voids the warranty so any future problems down the line are my problem.

I have for sale a beautiful walnut stock AGT Uragan .25. Like new condition. Purchased from Georgia Airguns. Had it a few years, never shot it. Holds air just fine. stock is perfect. Comes with 4 magazines and a Donny moderator. Priced to sell. $700 shipped to lower 48. PayPal friends and family or Apple Pay only. I can talk or text about the sale. Just PM me for number.

I have a really nice FX Maverick .30 cal that’s highly upgraded with bolt on parts. See for yourself in the pictures. .30 cal with 600mm set up. Holds air just fine. In excellent condition. $875 shipped to lower 48 PayPal friends and family or Apple Pay only. Glad to talk about sale. Just PM me for number.

Have a very nice, like new taipan veteran that I bought a few years ago and never shot. Like new condition. Holds air just fine. Have an extra Huma regulator I never installed. I am missing the two magazines. I don’t know where I put them. Knocked $100 off asking price so you can buy a few to replace. $650 shipped to lower 48. PayPal friends and family or Apple Pay only. Totally fine sharing phone number so we can chat. Just PM me.

I have a 35” Skout Epoch in .22 cal. With the pellet barrel.
Shooting JTS 22.07 off bench. Accuracy can be stellar out to 100 yards when the barrel is in its happily seasoned state. However it only shoots fantastic for 40-50 shoots before the barrel collects large amounts of lead, mostly within the first 10” near the breech end.
I understand that JTS pellets may flake more than JSB and other brands. I’ve tried 25.39’s in both JSb and JTS and neither are as accurate as the 22.07’s, tested at 875-1050 fps.

The biggest inconvenience is that once the heavy leads deposits are removed, it may take 16-30 shots before the barrel is back to superb accuracy , only to fall off again. I’m hoping to get a few tins of JSB 20.83’s this week to test with.

I easily have 7000 rounds through this rifle, so I’m familiar with this Skout.

My question is basically what products remove lead in this new barrel the best?
Also I find it best to clean before accuracy falls off too far, it seems to recover from the cleaning quicker.

I talked to Skout and they recommend Premium Quality Starting Fluid.

I’ve used Balistol, Super OCG, Starting Fluid, Brake Cleaner, and Birchwood/Casey Gun Scrubber.

I really think that a bore cleaner like Shooters Choice or similar might brake the lead up quicker. But I really need to go after a repair for the cause rather than repair the effect.

Hoping to hear your suggestions and solutions.

Thank you.

Is there a quick formula to calculate the range added by height of target?

I hated geometry, I always despised it in school. I'm wishing I listened now, as I should know this as a college educated 38yr old who's worked in trades as well as behind a desk in a business setting.

Does +2% every 10+ in height seem accurate? Once again this is probably a no poop answer, I'm just a dunce in anything other than basics, statistics, algebra. Help a retard out.

Congratulations to the winners!

89 - @850renxrs
16 - @Pavelow
55 - @Spinach

Thanks for participating, and a HUGE shout out to Thor Molds for making this happen!

As stated, looking for a lightly used viper in .22. May look for a 25 if I can't find the 22.
Thanks for lookin!
Chris

Got a bunch of pellets and slugs in .25 I used for testing. Will trade for .25 33gr Zan slugs (dish base)

One tin of FX 34gr pellets.
2 tins of JSB Exact King 25.39gr (one full and one nearly full)
1 tin of JTS 29gr
Zan 37gr slugs (about 140 of them)
Zan 45gr slugs (almost 200)
AVS 30, 34, & 40gr. (kind of a sample pack: 50 - 100 of each left)

Let me know if you want them, and if you have Zan 33gr to trade. Thanks.

I have lots of arrows that I have damaged over the years. Of late I have been using them to mark known woodchuck burrows, etc… Then I range find the distance and gain an advantage over the critters… Today I marked three different locations where the chucks saw me first…

Sales Rules:

• I accept PayPal or Venmo - F&F only. Not my preference, but if we've done prior transactions I will accept check or USPS MO.
• CONUS shipping is included in the asking price.
• I go based on PM timestamp.
• Please - no trade offers for this sale.

I have a solid reputation on AGN as an excellent seller and buyer. Can provide member references upon request.

As part of an ongoing reduction in my number of airguns I am putting up my Zeus .72 for sale. This is a Gen 2 Zeus with a 16" barrel. Capable of putting out 7-800 fpe depending on weight of ammo used. I purchased this beast of an airgun new from The Pellet Shop in early 2022. In the time I've owned I've taken it out a bunch of times and never had any issues. It's got some kick due to the power level and short barrel and it pretty loud, but puts a big smile on your face.

Looking the Zeus over there are a few tiny marks on the stock. The barrel nut is showing some wear from tightening it down after removing the barrel for cleaning.

Included in this package sale:

• Zeus .72 16" Gen 2
• DFL Great Kami with M20x1 and M18x1 connectors.
• Monstrum G3 1-4x24 FFP Scope w/ QD Mount
• Cheek riser for stock
• Forward vertical grip handle
• Mr.Hollowpoint Ammo
  • 460 grain - Qty 14
  • 525 grain - Qty 28
  • 530 grain - Qty 100
  • 630 grain - Qty 21

Purchased separately the rifle, scope, moderator (N/A anywhere afaik) and ammo would total over $1900.

Asking Price: $900 $850 SOLD

Just had to replace a broken valve pin again on my AEA HP SS .30. This is the 2nd time now. Is there a reason they are made of plastic?

When I pump my gun (Uragan 2), both gauges seem to be in sync.
However, an odd thing happens when I start pumping. First few pumps, the pressure in the hose starts building up. Then, it stops and starts moving incrementally, I assume that's when the tank is starting to get filled. But that happens at a much lower pressure than the tank gauge is indicating. For example, I stop shooting my gun when it drops just below 200 BAR. When I start pumping, first few strokes, the gauge needle advances rapidly. Then, at about 150 BAR, it stops and start moving very slow. Makes me wonder if my tank has 150 or 190 BAR in it.
Any idea what's happening and why?

Also, my pump has fine dust residue the same color as filter material on the bleed valve. Is that an issue?