Hello everyone, been gone for a while but I’m back now. Anyone know where I can find spare mags for a .177 akela? Sent out a few emails but nothing back yet, can’t find them anywhere. Out of stock pretty much everywhere or just not listed anymore. Any help would be awesome, thanks!

hi.. I'm quite new to this and I love it, but recently had a problem with my artemis p15, I brought myself a new one a few month's ago now and the bloody poppet snapped off at the end so I ordered some poppet's from Ali express but unfortunately they are too long and a little bit thicker than the original poppet (tipical) I don't suppose anyone with some professional knowledge would know how to get them to there correct size, what would I have to buy in order to get them to my desired length?? I'd really appreciate any help and or advice

I recently (3 weeks ago) bought a Snipe 2 and yesterday while at the range I heard a leak near the end of the day. I'm assuming I may of blown a O-ring somewhere near the breach. But I can not find one resource online that shows you how to take it apart so I can even do basic repairs. Does anyone know where one could find resources for basic repairs on the Snipe 2?

So I am trying to find out if anyone knows what size o - rings are in the standard Airforce Texan 457? Any information is greatly appreciated. What I'm trying to do is replace the Airforce standard o - rings with green helium rated o - rings so I can shoot dry air , nitrogen gas as well as helium when I want that extra power when deer hunting for flatter shooting slugs at longer distances and obviously more fpe. Yeah I know I could get the T - Rex in 457 and that's the plan but for now helium will do the job if I can figure the size the o - rings are in the standard Texan long air rifle 457. Thanks for any information given in advance. Much appreciated.

Hello,
I have had this Crosman 2240 collecting dust and I was thinking about a project to upgrade it. I still want to keep it as a CO2 powered pistol, but I was thinking about adding a new receiver that would accommodate a barrel shroud. I'm hoping I can make it a little quieter for shooting in my shop. There are not a lot of options for high breeches, and they are also quite expensive. Do people have any suggestions? I have some machinist friends. Are there CAD files around that one could acces?

Thanks!

My LP 5 shoot 2 shots at a time.
Any suggestions for solving?

Hi I have just brought the ATN x-5 series scope and I have no experience set this thing up and I can't seem to pair it to the wi fi.
Is there anyone out there that could possibly assist
Thank you all.

Any thoughts out there as to why my Epoch leaks from regulator when trying to fill? I’ve had a call into Skout Tech Support for days but nothing yet.

So I put together the DIY Daystate programmer and wanted to tune it a bit but when I ran the program it seems pretty freaking high already!

At High Setting it is shooting 13.43g JSB Knockouts at 978 fps..... and shoots 16.5g Varmint Knockers @ 894 fps.

At medium setting it is shooting 10.03 JSB MK3's at 1018 fps

I wanted to set the High setting a bit higher to get the 16.5g Varmint Knockers shooting at 980+ fps but with settings already so high is that feasible.

This is my Chinese-made cheap chrono. It was working pretty well with my 300mm barrel, until I upgraded it to 500mm. I'm using an FX Dreamtact. I've tried indexing the liner, and now it can read slugs (11 grain). Pellets (10.34gr) have to be tuned down pretty low, below 650fps for it to read. As for slugs, it has no problem reading any velocity. This is a bit perplexing for me. Can anybody help me out?

is the phone mount of the sideshot as good as the GoPro? Digital scopes are not legal in my state.

Hello.
I am replacing my brother‘s air tube on his MA2 .30 cal. with the new version. I figured while I was in there I might as well polish and lube the reg. The problem is as I disassembled the reg some of the belleville washers did not come out on the post and now I have no idea which way they were turned. Some help please, I couldn’t find any info on here or on Macavity’s site. Following is what I think the stack might be but not positive. ))(())(())(())(( Thanks

I just got a reximex throne gen 2. My first pcp. I shot about 25 times and then the cocking handle wont stay in the home position. Any advice would be greatly appreciated.

i degassed my wildcat today to add a reg in place of the brass plug. filled it up seemed to hold air pit ear next to gauge. went back to check on it 4 or 5 hrs. later and 0 pressure. so i gassed it up again. its leaking past the oring on the breech end of the cylinder? didnt touch that. my question is , by degassing does this sometimes happen where orings are compressed and just dont seal again.?
next question……
the parts list shows the oring as a 23mm x 2.5mm. is the 23 inner or outer dia. not sure how fx sizes.
thanks!

Is anyone shooting heavy slugs out of the FX leopard 70 grains and above if so what are your regulator micro and macro settings for 30 cal 700 mm sniper

The compression tube has squished itself into a pancake style burr. Of course this has also damaged the oring. There does not seem to be any damage on the barrel side, except some light marring of the finish.

Should I locate a replacement compression tube or take the part out and file it down?

1 oring was removed to take this picture and the gun has under 1,000 pellets.

Hey folks is it just rumors or is aea in fact discontinuing the challenger standard?? I've heard the 357 standard is no longer available thats in both 30" barrel and 24" as well
This series regular or max power kit .is by far ur best budget big bore out there .like to know if anyone else heard this

My question is I have an fx impact mk2 22 cal with 700mm barrel tension kit with 720 plenum and power block .can u tell me in steps how to tune so I can learn Ken Hicks tuned my gun to shoot Griffin slugs 35 grain at 970.my reg is at 150 .

Hi everyone,

I'm planning on buying a .22 air rifle.

I prefer compact models and came across the RTI Prophet series.

Now I have the option of purchasing either the Prophet1 Compact Performance or the newer P3 Compact.

Which do you think would be the better choice?

Also, does anyone know if you can mount a larger bottle (for example a Leishy 350cc) on the Prophet Compact models?

Best regards,

Max

try to answer questions,wouldn't that be called guessing?Does guessing really help? I guess it if your guess is the right one,I am just guessing because it could be wrong .My guess is the person guessing just wants to be to have the freedom to guess.Why guess,lookit it up...."Just the facts, ma'am"

Does anyone know where i can get an aea m50 (.495) valve sale. Aea's customer support has proven worthless.

Hi,

First post. I hope this is the right place!

I'm considering purchasing a .177 Leshiy 2 Short (REPR-X) with a 250 mm barrel. I would use it primarily for backyard plinking and secondarily for pest control.

I am somewhat concerned about being a noisy neighbor. Would anyone please comment on how loud this Leshiy 2 is likely to be?

I'm also considering mounting a thermal sight on the Leishi 2. Does anyone have any recommendations for a good thermal sight based on experience?

Does anyone have experience with this configuration? I would love to hear any details that you might wish to share!

Thanks for reading this far!

If I am understanding correctly, MOA is equal to 1 inch at 100 yards. So, when setting a scope at 100 yards the squares on the target are 1 inch and thus let you know how many clicks to turn the scope adjustments. So, in my case I am setting my scope to 25 yards. (Due to poor eyesight) even at this close range in order for me to see the small target/pest I have to use a scope. So, should I perhaps use graph paper with 1/4-inch squares as a sight in target to make the adjustments? Still trying to get a tight 5 shot group smaller than a dime. A steady shooting platform I am sure would help also.

Thanks for your feedback.

Hello,

I am looking for a long repeating lever for my Red Panda. Do you know anyone who can make one for me?

See attached image for example.

Best regards to all

I'm new to air rifles. Had a Slavia 618 breakbarrel as a kid looong ago. Shot many handguns over the years, and the F-15's M61A1 20mm gun for 3+ years in Okinawa. Now retired, I'm interested in getting rid of some pesky squirrels.

Learning to shoot lefty is not an option due to a slight defect on my left retina, even though it is my dominant eye. And using a traditional scope is a one-eye process as well, which won't work for me. I need to use both eyes, ergo a red-dot. I became reasonably good with handguns using a red-dot sight and both eyes. However I've been told by some knowledgeable airgunners that gas ram and spring piston rifles will destroy a red-dot.

So I'm looking for suggestions, maybe some combinations, from you dedicated airgunners. The red-dot I have is a Holosun 403B. I want a quality rifle and was considering a breakbarrel Weihrauch. I'd also like something mid-sized that my grandson could learn. Not a big fan of the extra equipment required of PCP or CO2 but these damn squirrels may dictate otherwise. Thanks in advance for your input.