Just found out my bobcat mk1 regulator is leaking an it seems to be the internal seals (o-rings) on the reg, does anyone know where I can buy these seals internationally or what the sizes are, I've included a picture of the regulator that is installed in this PCP

Repairing a Crosman M1, does anyone know the size difference in the Barrel Lock Spring? One fits the wood stock and the other fits the cross wood stock. I have a wood stock and have a spring from the croswood stock but it is to long for the barrel to be cocked.

How do you degas a FX T12 Whisper .22?

Why don't they make solid (non-HP) slugs in .25 and .30 calibers? I found a few but the calibers are just a hair larger (.257 & .308) than I can use.

Will the Fx impact regulator fit in the Panthera? I installed the extra high pressure Huma regulator and the recharge is very fast. The issue is the regulator drops in pressure over a period of time after shots and can’t hold the set pressure. For example I set the reg to 155bar and after a couple magazines it is at 152 bar with 170bar left on the fill. The stock regulator re charge was extremely slow but eventually got to set pressure. The stock regulator eventually creeped about eight bars higher then held that pressure. My idea was to get the impact high pressure regulator vs extra high so it had a bit softer springs to help the regulator recharge to my set pressure.

So I'm awaiting delivery of a fan-cooled and internal water tank-cooled air compressor and am wondering if I can leave the water tank (which I plan to fill with a 50:50 mix of distilled water & Water Wetter) filled between uses or if it is recommended to empty it. Thx!

So I'm awaiting delivery of a fan-cooled and internal water tank-cooled air compressor and am wondering if I can leave the water tank (which I plan to fill with a 50:50 mix of distilled water & Water Wetter) filled between uses or if it is recommended to empty it. Thx!

Does anyone have any experience with these regulators? I'm assuming it's top quality coming from Huben, but any knowledge of them being used on the notos? I'm contemplating getting one along with a .2l cf bottle.

Here's a pic of the notos currently.

I recently cleaned and greased my old Slavia 631 and after i reassambled it it would sometimes fire when i took it of the safety
Without pulling the trigger

Hi all,

I'm new to the forum and starting off with an odd question.

Can anyone tell me if the factory Impact M3 has any magnets in its build, especially the rear butt/block section?... Or the magazine?

I need to stay clear of magnets for medical reasons, hence the weird question.

Considering buying an M3.

I know some aftermarket bits do, but interested in the factory build.

Thanks!

Anyone know a good place to send a Benjamin 422 for repair. They are tricky to work on and wondering if there’s someone who specializes in rebuilding them

3 or 4 weeks ago, I bought a 700mm heavy .30 liner and have been working out various slugs (bought and cast) without much luck. I initially had decent grouping with 54gr Zan, but it faded away quickly. Since then, I have tried almost every manufactured variant I can find, ordered casting molds in different weights, tried different alloys, all sorts of tuning adjustments, and epoxied a carbon fiber sleeve on with no luck. I recall seeing some people talking about it taking a few hundred shots to smooth out the barrel and grooves, so figured i just needed to shoot it more.

Well, I've got through a ton of ammo and it seems more like the accuracy is dropping off as the shot count goes up, so I figured I would take a closer look at the liner bore to see if thats where the troubles were coming from. I'm seeing quite a few blemishes along the grooves, spots that look like little divets that go all the way around the ID of the lands, and what looks like a straight seam down the length of the ID. Ive gone through it a few times with JB paste, and even Flitz to see if i can get it to help clean it up with no real change.
Take a look (albeit the pictures I've taken aren't exactly the greatest, and definition of the spots isn't as apparent on them) and tell me what you think. I'm also pushing slugs out of the barrel at .2962-.2964", with slugs pushed halfway and backed out measuring a more standard .2989-2990". Most of the worst pitting is within the last 2" getting closer to the choke. I have been wondering how this liner gets dirty so quickly, but now it seems that these spots are scooping bits of lead from slugs and pellets. Is this just a bad barrel? It's been frustrating me since I can't use this rifle until I know I can make responsible and accurate shots. The original .30 liner that came with appears nearly perfect, so I'm guessing either the choke side of the jig or the liner blank itself had nasty bits stuck to it before it was formed.

I have a Quackenbush Outlaw and would love a holster for it, but I'm not sure what would work because of the bolts on the left. Does anyone know what would work?

I'm looking to try to hot rod a Texan .457 because I love airguns and Quigley Down Under lol. In all seriousness, I love tinkering with things like this and I have a bit of a mad scientist idea. I emailed the guy who runs African Air Ordnance and he did confirm that his valve can handle 5500 psi. The problem is that I can't find any air tanks or bottles smaller than like four or five liters. Could anybody offer some input or maybe some leads on where I could source something like this? Thanks everyone.

Hey y'all. Can anyone help with removing stuck slugs in my Benjamin Bulldog .357? My friend unknowingly pushed 3 -142g slugs and I can't not remove them for anything. I tried spraying Ballistol down the barrel and soaking over night, then used a push rod to try and remove the slugs back out of the breach. They didn't budge at all. Do I need to let the air out and remove the barrel? If so, are there any good vids on how to do so? Thanks for any advice in advance. I hope the barrel in not ruined, errrrr.

I have a compressor and before I changed my oil it used to fill my pcp all the way up to 4500 psi and after I made the oil change it takes forever to fill and it fills only to 4000 psi if I’m lucky

I'm looking for recommendations on a bottle to store my Ballistol in with a pen dropper that does not leak every. Anyone have one they use that they are 100% satisfied with? I have attached a picture of what I am looking for.

Hello I'm looking to buy my first pcp and kral arms seems to be from the better options for its price.
I'm looking at kral puncher shadow which is regulated in either .22 or .25 still hasn't decided I'll plink up to 100 yard. Did any of you own this rifle or shot it?if yes what's your opinion on it any remarkable problems?

I might grab instead a kral arms puncher jumbo dazzle which is unregulated which from the reviews on the internet they seem satisfied with it .
should I grab this which is 100 usd cheaper or go for puncher shadow?

I have a 362 Crosman which I love, I stupidly put some gun chamber lube in the air tube, the gun would not build pressure, I called Crosman and they gave me a tip on what to do, it didn't fix it , tried an alcohol flush, didn't work, now I have air in the chamber that I can't get out, they told me to cock and fire without any pumping, I have done this several times, will this solve the problem? I don't really want to have to send it in. Thanks

Howdy all.

I've just bought a vertebrate pest control business, and am looking to get into shooting smaller pests such as rabbits, pigeons, rats etc.

I've got an array of firearms, but no decent air rifle. I'm looking for advice on what rifle (pcp) would best handle aussie conditions, and will be suitable to take down rats through to foxes. Been looking at the FX Impact M3 and Maverick, but mixed reviews have me cautious on dropping $3k+
I like the bullpup design for its compactness while not compromising on barrel length. Looking for probably a 600mm or 700mm barrel.

Does anyone have any suggestions? I'm in south australia, if that helps at all.

Hello sorry to bother
I recently got into air guns and specifically air revolvers. I bought a barra Schofield no.3 with 7” barrel and after tons of fun I was wondering:
Is it possible to machine a seal or valve that releases more co2 for the pellets to be able to travel faster or with more energy to really break some glass bottles or stick further into wood
I have tested different pellets in .177 the crossman piranha and gamo magnum being nice ones, but they have yet to really break a bottler or stick into wood
They can kill possums and squirrels pretty dam well though for anyone wondering
Thanks in advance

can anyone help with hatsan blitz. it’s brand new and won’t take air. the value is properly sealed and there are no leaks. i asked hatsan and they said that if it’s been sitting with out air for awhile you need to take air tank off but it won’t budge even tho its completely empty. any suggestions? thank you.

Hello, I have an Edgun Matador, I suppose from the first series (#1862), and I am looking to replace the firing valve. I would appreciate any information on where I can buy it.

Has anyone tried putting on a regulator on a

Niksan Ozark? Really want to buy one but not having a regulator kinda turns me of even though according to my research it's already quite accurate. Now imagine what it could be capable of with a regulator on it. I know it's a fairly common thing to do on other PCP rifles but I can't find anything about putting one in the Nissan. Just trying to figure out if it's been done and if so how was it done and what where the results?​