Love my zelos , theres no crap or filings. Was surprisingly a clean if slightly oily barrel when new
Upvote 0
Snowpeak Snowpeak M60b or Umarex zelos parts list
- Thread starter charlie99
- Start date
I am no expert on the M60 or Zellos but I have tuned a Stoeger bullshark and my P35s and that experience suggests the guns made by SPA are, if anything, better than the ones sold as SPA. Stoeger may have done a little engineering to facilitate that. The more compact but still effective baffle stack and the steel (instead of pot metal) rear screw attachment point are my examples. Later P35s may have the steel block. SPA seems to prefer selling guns through others so I see no logic in suggesting they would be worse in quality. I believe they are essentially equal.
Upvote 0
i had a few factory caused issues with my M60B:
- fill adapter's foster fitting was missing a bit, so it did not work (got a working spare, from the vendor)
- deep scratch in the bottle connector o-ring groove, that lead to broken o-rings/leaks. (fixed by proper polishing)
- steel chip from machining in the groove for the o-ring inside the barrel breach, that caused the o-ring to erode in one spot and lead to loosing power. (fixed by taking out the chip and replacing o-ring)
Upvote 0
I have been very happy with my 22, especially since getting it from gun zone deals for $420.
Upvote 0
i am not unhappy. it was my first airgun and i learned a lot. i wish i would have gotten the .30 and not the .35cal, though.
after porting and installing a power-valve, it is quite a cannon and precise too.
Upvote 0
It was a simple M18 x 1.5 male to M16 x 1.5 female. I had to use blue thread locker to make it work , and it was made from brass. Now I have an adapter made by c88machining it was $50 it's very nice , and let's you use the guage off the tube which is M8 x 1. I no longer use the paint ball flat bottom bottle I got from Walmart. I bought a round bottom aluminum bottle from Amazon for $40. I'm planning on getting a .25 cal Zelos , and I will be useing the Huben Zelos regulated bottle adapter , and a .7L Tuxing carbon fiber bottle , so I can fill that to 4.500 psi , and set the bottle adapter regulator to 3625 , and see how many shots I can get. I like very much that you can set the Zelos reg to 3,000 , so it will be my new slug gun , and I may even install slug power kit in it.
Upvote 0
I also have the bottle adaptor and plenum add on from C88machining. With my reg at 2100psi I can get 84 accurate shots. So far my Zelos shots the AEA pellets from 25-33 grains very very well and for some reason at the same settings it really shoots the H&N Baracuda Hunter Extreme 28.24 very well. Just started some slug testing, the H&N slugs 30 gr and the Apolo 33 grain are bug holes at 35 yards
Upvote 0
I have been looking for a Zelos bittle adapter (reasonably priced) for a long time.
Where did you find the "M18 x 1.5 male to M16 x 1.5 female" adapter?
Does it seal and work well?
I know about the c88machining adapter but it is $60 after tax and shipping.
Upvote 0
It was on eBay, but you won't have a way to fill the bottle. I moved my guage , and foster quick connect to the plenum. I would not do this again , and the bottle adapter from c88 is the less expensive way to go.
Upvote 0
Been looking everywhere for a m16x1.5 female to g1/2-14 female to run a Chinese regulator on the zelos.
Upvote 0
Steve , question what size is the zelos male filling on receiver?
Is it the m16x1.5 you alluded to?
Upvote 0