Other AirForce Knockoff First Look + Other Pinty Guns

[smythsg]

Received the P-RIFLE today. No damage to box or rifle. Aired up and shot 10 shots with 14.3 averaging 904 fps and 21.6 fpe. Had a high of 911 and 1st shot was low at 895 fps. Came with 2 mags and o rings. The mags load into breech from the lt side but the BARRA 1100Z mags fit perfect and load in from rt side. I think the BARRA mags will fit the P-PUP also. Both are 10 shot and BARRA has them at $12.00 each. First impression is it is light weight shoulders well and cocking is a little heavy. trigger feels great right out of box. Has been sitting for 4 hours with no loss of pressure. Right now I have the flu but hopefully by the weekend will do some testing.

View attachment 540224

View attachment 540225

View attachment 540226

Going to take a chance and order one of the Barra mags to see if it will fit the Bullpup. I'm a bit skeptical, but will be very pleased if it fits.

 

[Avator]

Tracking update says Tuesday 2/25 on the PForce. We'll see.

 

[nobody1]

Going to take a chance and order one of the Barra mags to see if it will fit the Bullpup. I'm a bit skeptical, but will be very pleased if it fits.

I have the Beeman (AKA Barra) magazines.
I will try them in my bullpup.
I am sure they will not fit the bullpup.
They may fit the rifle.

UPDATE
Just tried the .22 Beeman magazines.
They do not fit the bullpup.

 

[smythsg]

Sorry to hear the mag will probably not fit the Pup.

 

[billygee]

Wanting to know how loud is the 10 shot Long Gun from Pinty
Is it Back Yard Friendly or still need a Moderator on the end of it ?

Bill

 

[nobody1]

Wanting to know how loud is the 10 shot Long Gun from Pinty
Is it Back Yard Friendly or still need a Moderator on the end of it ?

Bill

I have similar questions of the Pinty rifle.
1. Thread size on the moderator adapter ?
2. Is there a real shroud ?

 

[rdpjr6504]

Been in bed with flu only shot 1 mag. Barrel is tensioned on with an adaptor holding an empty carbon shroud with holes in it. The adaptor is threaded 14 x 1 just like my P-FORCE. The mod on my P-FORCE fits nicely and quiets it down. Seems not too loud but do not have a meter. I read BUCKRAIL has mods but I looked and nothing in 14 x 1 only 14 x 1.25 threads. Also barrel is screwed into breech and has I believe -will check later- barrel has 1/2 x 20 threads. Hopefully this weekend will be up to testing.

 

[rdpjr6504]

@nobody1-- The barrel adaptor has holes in it that redirect air towards back of shroud. I will take some images later tonite.

 

[rdpjr6504]

Here is rifle barrel off. The DFL TANTO 1/2 X 20N SCREWS OINTO END OF BARREL BUT NOT ADAPTOR.

 

[billygee]

Been in bed with flu only shot 1 mag. Barrel is tensioned on with an adaptor holding an empty carbon shroud with holes in it. The adaptor is threaded 14 x 1 just like my P-FORCE. The mod on my P-FORCE fits nicely and quiets it down. Seems not too loud but do not have a meter. I read BUCKRAIL has mods but I looked and nothing in 14 x 1 only 14 x 1.25 threads. Also barrel is screwed into breech and has I believe -will check later- barrel has 1/2 x 20 threads. Hopefully this weekend will be up to testing.

few more questions on the ID clearance between the barrel and shroud
Just to clarify are both ends of the barrel 1/2 x 20 with the adaptor being 14 x 1 thread size ?
with this having a 18.1" barrel, how much of it is screwed into the receiver ?

Bill

 

[rdpjr6504]

The barrel is 18 inch but 1.5 inches screws into the thimble that secures barrel to breech. Threads on breech side thimble are smaller than 1/2 x 20. Reminds me of the way the PP750 barrel attaches. Without measuring looks to have 1/8 inch clearance between barrel to shroud.

 

[Waters in the woods]

Aluminum can for the win. Shim around the loose part. I did it in a hurry to see if it would work, it does amazing. It's held in place by the bolt, I'll go back and do a better fit now that I know it's worthwhile.

 

[Avator]

That is basically what I had in mind but I was going to try aluminum tape and maybe lay it in the trough under the cylinder. I don't have the gun in hand yet so I'm just winging the thought in my head.

 

[Johndeere400]

Update on Pinty work in progress. Profiled sear and got trigger to 4.5 Lbs. Tore apart again and put more curvature on sear and got trigger down to 2.5 Lbs.

Feels really good now with no catches in trigger pull. Off to range tomorrow to try it out

 

[SpindleB]

Aluminum can for the win. Shim around the loose part. I did it in a hurry to see if it would work, it does amazing. It's held in place by the bolt, I'll go back and do a better fit now that I know it's worthwhile.
View attachment 540542View attachment 540543View attachment 540544

I know that scope, Wipoten 6-24x50.
Love the 3 large picatinny rails and the built in mount. It is sold under various names but a very good scope for the price.

 

[SpindleB]

That is basically what I had in mind but I was going to try aluminum tape and maybe lay it in the trough under the cylinder. I don't have the gun in hand yet so I'm just winging the thought in my head.

When it was discussed elsewhere I suggested Teflon tape so it would not bind.

 

[rdpjr6504]

I think his scope is a PINTY 4-16X50 OEG. Fitting for a PINTY rifle.

 

[SpindleB]

I think his scope is a PINTY 4-16X50 OEG. Fitting for a PINTY rifle.

Yeah, it is the 4x16.
Just looked on Amazon, the price was $59.99 when I bought them and now it is $89.99
Wipboten was what I bought
Pinty, MidTen, UUQ and no brand.

 

[Gault]

Update on Pinty work in progress. Profiled sear and got trigger to 4.5 Lbs. Tore apart again and put more curvature on sear and got trigger down to 2.5 Lbs.

Feels really good now with no catches in trigger pull. Off to range tomorrow to try it out

For those that are re-profiling their sear, what tool/machine are you using to remove the material?

 

[Waters in the woods]

For those that are re-profiling their sear, what tool/machine are you using to remove the material?

I used a grinder then file then 320 grit wet or dry paper and finished with 1000 grit.