iIt's here watie is over.. frist one was Bad ship it back.. an the Brown box showed up today... with the replacement.. i got to shoot it few times before Dark.. i love it... scope incomeing next ... am all ready looking in to buy a another one.... not sure whats my next guns going to be...

Benjamin Marauder in .22 cal. With UTG Bug Buster Scope, 2 - Magazines, Carbine Stock & Grips included. Excellent Condition $300.00 shipped lower 48
email: [email protected]

I’ve got an FX Revolution in .22 caliber with the LOTHAR WALTHER barrel. Pretty cool. As much as it pains me to let it go (considering that I searched for this rifle high and low), I simply don’t have time to tinker with it. I got it shooting.

Comes with 1 magazine and a fill probe

Sold

New to PCP guns, but learning a ton. I'm getting closer to deciding on what gun to buy. I'm down to the Avenge-x carbine and the XM1 Scout, both in .22. My shooting will be more in line with pest control inside 50yds with occasional longer shots. I like the idea of having ability to make adjustments externally. For those with the XM1 I have a couple questions: 1. Can the regulator be externally adjusted? 2. How is Stoeger when it comes to warranty and parts support?

Maybe I'm making too much of the ability to adjust the regulator? The more I dig it appears that the hammer spring adjustment works in balance with the regulator prx. Is this correct? My guess is that once I get this gun set up for my needs with a heavy pellet/slug, I'll leave it alone and just use it.

I also have no compressor. Sounds like both of these guns will be too much for hand pumping?

Bang for the buck it appears that the XM1 takes the cake, however I don't know what I don't know being new to this dance.

I also posted this on HAM for some extra points lol and figured I would post here as well. I'm a little confused with the pricing for the different barrel lengths and configurations. Can someone check my math because the math ain't mathing.



For the walnut tube version, the prices off AOA's website are the following:

- 17 inch version is $2,899.99
- 23 inch version is $2,999.99
- 28 inch version is $3,199.99

The cost difference between the 28" and 17" version is $300.00. 28"-17"=11". $300.00÷11"=$27.27 per inch. If you were to go from the 17" to the 23" version, the cost difference is $100.00. If you subtract 23"-17"=6". $100.00÷6"=$16.66 per inch. If the forend and tube cylinder are the same size, you would be only paying for the additional length for the barrel and shroud. I don't get it.



Now for the Grey Laminate tube version, the pricing is as follows:

- 17 inch version is $3,185.99
- 23 inch version is $3,199.99
- 28 inch version is $3,449.99

The cost difference between the 28" and 17" version is $264.00. 28"-17"=11". $264.00÷11"=$24.00 per inch. If you were to go from the 17" to the 23" version, the cost difference is $14.00. If you subtract 23"-17"=6". $14.00÷6"=$2.33 per inch. If the forend and tube cylinder are the same size, you would be only paying for the additional length of the barrel and shroud. I don't get it. Also, it looks like the Grey Laminate version is actually cheaper than the walnut version per inch.



Now for the chassis version, the pricing is as follows:

- 17 inch version is $3,294.99
- 23 inch version is $3,494.99
- 28 inch version is $3,699.99

The cost difference between the 28" and 17" version is $405.00. 28"-17"=11". $405.00÷11"=$36.81 per inch. If you were to go from the 17" to the 23" version, the cost difference is $200.00. If you subtract 23"-17"=6". $200.00÷6"=$33.33 per inch. If the forend and tube cylinder are the same size, you would be only paying for the additional length for the barrel and shroud. I don't get it. The chassis version is more expensive per inch then the other two versions.

The pricing just seems all over the place. Help me understand. I suck at math. Love your airguns but this is just way off. If you look at FX, their different barrel/shroud length versions seem more structured.

This is my improved Spring Doc.
One of Oak,
Other is Black painted Beech.
They will work with any Spring pistol or rifle. Up to the Diana 350 Magnum.
$225.00 plus actual shipping cost. Price is for one compressor.
email [email protected]
USPS Money order or paypal friends and family, or paypal + 3%
Price dropped to 225.00
This is the best compressor out there in my humble opinion. These are the last two available and I won't be building more for some time. When you consider material costs and time spent making them, it's a good deal . Cheers

WTS: Unfired MROD in 25.

Never had a scope mounted.

asking 375.00 shipped. Venmo.

Hello all-

I’ve a Ukrain Vet 1 and Vet2 for sale. I’m only selling one, I’ll keep the other one. Can’t justify having 2 bullpup doing the same thing .

Vet 1: .22 cal
Condition 8.5/10
Mechanically 10/10
CZ barrel ***MADE IN UKRAINE***
Will come with all the oem stuffs and barrel cover(pictured)
And 6 mags, 2 oem and 4 resin mags(made by me). You can pick between reg mags or anti-empty loading mags.
Price $950 shipped within the lower 48

Vet2 tac standard .22 cal
Condition 10/10 only 3-4m old, never left the house.
Mechanically 10/10
Unchoke CZ barrel
Will come with oem box and stuff
And 6 mags, 2 oem and 4 resin mags(made by me). You can pick between reg mags or anti-empty loading mags.
Price $1250 shipped within the lower 48

This is for the bullpup only, no scope or bipod.

Only 1 option: Hawk 4-14x44 for $200 more.

For faster response
8fi8-876-tutu64.

FREE pick up in San Diego.

** SOLD **

Whatta deal for only $300 -->

I purchased this Talon SS from the AGN classifieds recently, mostly because I'd read so much about AirForce air rifles over the years but had never had a chance to actually try one.

The previous owner had switched out the original 0.25 barrel with a 0.22 barrel. The label on the box still shows 0.25 but it only has the 0.22 barrel with it. I shot about a hundred test pellets through it at close range. It works fine and appears to have hardly been used. I also purchased a solid cocking handle knob to replace the foam rubber knob cover which I never installed. I'll include that, along with the padded Nylon Bulldog carry bag (shown in the attached picture) I got for it. There is also a small tool to help when removing the air tank and manual & misc parts as shown.

This Talon SS is a very simple and robust design with little that can go wrong. The adjustable power settings and modest sound report are big benefits of this SS design. The Talon SS is a dependable, reasonably lightweight, sufficiently quiet and powerful airgun for light hunting.

The asking price is $300 for the items shown shipped CONUS. That's considerably less than I recently paid for the rifle itself without the Bulldog bag or aftermarket cocking handle knob. If interested let me know and I'll send my PayPal info.

I've gotten many of my best airgun buys over the years from AGN and other airgun forum classifieds.
It's the only way I could ever afford to try many of the airguns I've read about in the forums.

Thanks for looking!

Jpiperson2002














T

** SOLD pending receipt of payment **

I bought this .25 cal Huben v3 GK1 Short pistol new from Krazcool in the Fall of 2024. It comes with the upgraded pellet loading gate and a threaded end cap on the barrel. I mounted a Holosun HS507K X2 pistol sight on it and shot a few magazines of different test pellets through it at paper targets shortly after getting it. Around the same time I got a couple of other Hubens and this one never got any use.

It is in excellent condition, with no dings or obvious signs of use. I didn't change anything on the gun since I got it other than to add the 3D printed mounting bracket on top for the Holosun sight. I'll include a soft nylon holster which holds a GK1 with a sight mounted. Not so much to carry it around in, but more as a convenience for storage since the the foam cutout in the original GK1shipping case isn't large enough to hold a GK1 with a sight mounted on it.

The Shortened .25 GK1 pistol and the Holosun HS507K X2 sight with its mounting bracket and the holster cost me just over $2,000 within the past 6 months. My asking price on this one is $1,350 shipped CONUS. Everything will be very well padded and boxed. I've never had anything damaged during shipping over many years and hundreds of online sales.

PayPal only, No counter offers or trades considered. If it doesn't sell at the current asking price I'll eventually decide whether to lower the price a bit or just keep it. If I didn't already own 2 other GK1s I might just snatch this one up at this low price myself.

The Classifieds really help to keep the forum interesting for me.

Thanks for looking!

Jpiperson2002

Shoots pellets great! 3 mags and a bipod.

I have this Kalibrgun Cricket 22 that shoots like a laser, but I almost never shoot it and am looking for something new to play with. Cricket is currently tuned to shoot 18.1gr @ 923 fps with an es of 9 over an entire fill. I also have plenty of seals, probably 5 or 6 sets and a brand new Huma reg, never installed. I bought the seals and reg in case I needed them and so far, never had a single failure. Also have the tool to take the gauge out if ever needed.
I'd take $850 pp
I'd like to trade for something I will shoot a lot.
I like Brocock Snipers
Impacts
Crowns
Anything I haven't had before would be of interest, let me know what you have.

Cleaning out the parts shelf

1. Thor LT 3-6 $500
2. Discovery NV001 with laser NEW/UNUSED $250
3. 2 - Bushnell TRS-25's NEW/UNUSED $100 for both or $55 each

NOTE: sorry but the UTG BugBuster Discovery 4-16, & the Pard NV008 have been sold

Everything is in "Like NEW" condition and the new stuff... Well that is in NEW condition.

Shipping is on you. I would encourage you to use PirateShip.com as I have saved a ton since using them. Additionally by you creating the shipping label YOU get to choose the manner of shipping and how much insurance you want. Lastly, if a claim is needed for any reason you control that and get reimbursed from the shipper.

If you have any questions or would like more detailed info/photo's your welcome to call or txt me at 847.715.6944

I have a Hawke sidewinder 6x24x56, looking for a wheel that can be used for hft target shooting, plus be able to turn on my Illumination thanks

Hello all, I'm new here and don't know much about these old air guns. I picked up a couple of rifles at an estate auction. The one I'm trying to date is a sheridan. From all the reading I've done, I believe it is late 1950's. Please help and educate a newbie. The other one is a Benjamin Franklin

I'm just wondering what experience people here have had with them. One of the really nice things about evaluating a PCP is that you can shoot it from a rest and remove 90% or more of the human error from the equation. It doesn't matter if you got 2 hours of sleep last night and compensated with 5 cups of coffee. If the gun is capable of it, you can still shoot tight groups from a bench with the right gear. When shooting a springer on the other hand that's often not the case some guns just don't like being rested in certain ways or might shoot accurately but to a different point of impact. Even shooting from a rest is a bit of an art with a springer.

It's got me thinking about making a rest that would use drawer slides and Bog Deathgrip style clamps to hold the forearm and pistol grip. Something like that would allow the rifle to freely recoil and should provide a repeatable hold.

I have a magazine modification which members might find useful that prevents double loading of the magazines.

sold
Texan SS .457 - beast!
everything in picture is included with moderator
price includes shipping insured
$985.00 with scope
$785.00 without
buy with confidence as I have lots of positive feedback
PayPal FF
Venmo
Zelle
note* checks or money orders must completely clear bank before I’ll ship
for quicker response text me at
251-610-8582

i am helping @GulfCoastShooter sell this Airgun and I inspected the gun today and it looks brand new…and functioning perfectly if I was a hunter I’d buy this for myself!!

Looking for some sort of hammer upgrade for a Brocock sniper XR magnum in .25cal.
Have done some searching and can’t seem to find much for this model.
Not my gun but just seeing if anyone out there is cranking them up. Working up to heavy slugs, currently 941fps in 26.5gr maxed out or 904fps in 30gr. The end goal is to get to 36-40gr slugs in the 975-1025fps hopefully but it’s out of hammer.
Didn’t know if a heavier hammer or heavier spring was available.

Thanks in advance.

This is my homemade stock that I made for a Raw TM1000 that I purchased as a lefty, knowing full well that I am a righty. It took me 4 or 5 months to get started on it because I wanted to make sure that my shop was clean and ready to take on this project. I have previously made my first stock out of oak because it was what I had at the time and I needed to practice. I also made some stuff for another gun using laminate wood. It was definitely softer and easier to work with.

Shoots great. Tuned to shoot 18gr pellets at 900ish fps. 1st reg deleted. Saber tactical arca rail. Comes with 1 mag, fx factory mod, and Athlon Talos BTR 4-14x44 FFP scope. Comes in the factory hard case. $1650 shipped, $1450 without scope and rings.

Selling my Western Sidewinder.30. Zero issues. Excellent condition. Comes with 3 mags, soft case. Donny Tatsu is extra
Located in So Cal. Shipping costs on buyer. If PayPal goods and service +3%.
$1500. $1600 with Donny Tatsu
Sorry but not looking to trade

I sold my .22 air rifle and now thinking of getting another air rifle for hunting at <15 yards.
I was going to get another .22 but reading forums, the extra FPS/speed of the 177 would give me a better chance of a quicker kill on these pests at 15 yards or less

What do you think?

I've had an unregulated gen 2 Marauder .22 (Lothar Walther barrel) for two years now. I've put around 750-850 rounds through it - and until a few weeks ago, accuracy improved from reasonably solid to almost amazing since I bought it new. A few weeks ago, it started throwing one out of every 6-8 shots very close to 5 inches directly below the other 5-7 shots at 25 yards - and I can cover all of the other 5-7 shots with a dime (with those shots being centered on my aiming point). The one flier is always very close to 5 inches directly below the other shots and the other shots are always a very tight group where I would expect them to be. Could anyone offer any thoughts on what might be causing this?