I have ordered a number of the Beeman pcp and wanted one of several. Today my Commander in .22 came in and when I went to store the box I saw another box just like this one. And starting to look for the other one and I was. Setting about 6 feet from it and sever more. Don’t know how I missed when I thought I had carefully check what ones I had. Anyway isn’t two always better than one. Charles

Impulse purchase. Purchased during the July 4th sale. Ordered the Mad Dog stock and Altaros regulator shortly after receiving the airgun. Regulator works really well, it's set at about 135 bar and shoots the 13.73 JSB's at 740 fps. I shot it yesterday and got 70 shots with an extreme spread of 11 fps. If you want more power the regulator would need to be turned up along with the power wheel. Before I added the regulator max fps was in the 840's. The auto safety has been removed. There were a few places on the air tank that were chipped (see pictures), I've touched them up since I took the picture and they're not noticeable unless you're looking for them. I took my Impact 480cc tank and it used temporarily. Fits perfectly with the Mad Dog stock. THE .48L TANK IS NOT INCLUDED IN THE SALE IT WILL COME WITH THE ORIGINAL TANK. I just wanted show how it looked. Got a little bit of a hangover with the original tank but works fine and does not affect my hold at all.
Scope and rings not included
I've got well over $800 in this setup, selling for $600 $550 shipped CONUS, Pay Pal F&F or buyer pays fee.

still being green to this sport id rather ask than make mistakes
so my questions are
how often do you clean the barrel
do they use a brush like 22s or a soft swab I'm thinking a brush would ruin an air gun barrel but i could be wrong that's why i ask

which cleaning solution? something with silicone base?

use patches like a 22 push through until they come out clean i would suspect

when not in use do you lube the barrel slightly or no

don't mean to be a pain in the arse
id rather measure 2wice and cut once
thanks

I’ve ordered a Notos and since I only shoot between 10 and 25 yards I would like to set the fps to about 600. Before I put the stock on I would like to adjust it slower. And help as how many turns it might take as I’ll be shooting 15.89 gr pellets. Thanks for your help. Charles

Feinwerkbau 300s .177 with Tyrolean stock.
Very nice rifle.
Used for 25 yard benchrest.
Clean, straight shooting barrel.
The rest block is held in place by a UIT rail in the stock.
The block, scope & mounting are not included in the price but available if interested.
Front sight included!

$850 shipped conus.
This is lowest price I'm willing to go.
PayPal FF or add 4% please.

*

Excellent condition Uragan .25 cal. No leaks no issues, outstanding shooter. Comes with two mags, soft case, moderator, and fill probe. No bipod or scope included.

$1k shipped anywhere in the US. Send a PM if interested. Thank you.

To clarify:

- Scope is an Sig 1-6 in Sig mount. It’s the cheaper $300ish scope.
- Bipod is made by Spartan Precision. Came on rifle so don’t know much else about it.
- Comes with .25 and .22 barrels.
- Huma and factory regulator.
- Spinning pellet dispenser.
- Digital gauge
- Crappy hard case.
- Extra O rings.
Price is 1900 OBO. Shipping and insurance is included.

Really hate to post this one but something needs to go and lately I find myself shooting this the least.

First the bad: it apparently has sprung a leak. It was sitting at around 190 BAR 3 weeks ago and now it’s at 109. It comes with extra o rings though!

Currently setup with .25 barrel but also comes with a .22 barrel. The .22 barrel has a few spots of surface rust on exterior. Im sure they would come off but I never tried.

Has a Huma regulator installed as per the previous owner and also comes with original. It also has the digital gauge installed.

Also has this fancy little pellet dispenser that is apparently hard to get

Bipod/scope also included. Will ship in a small hard case (nothing fancy) insured.

Payment either Zelle or PP f/f. I don’t do goods and services anymore.

If interested, send me a message with your number and I’ll text back.

Would consider trade for another compact/folding style PCP plus cash to me. Straight trade would do me no good at this point. Might also consider trade towards a HW44 pistol, preferably .22.

Thanks

$1900 obo for it all.

Just joined here used to be on GTA haven't been shooting much in a couple of yrs.I currently have a Umarex origin and a Avenger both in 22 along with a Gx cs4 compressor . I would like to find something in 30 or 35 cal to do a little coyote shooting noise is not really and issue I have a small farm in the county and have several coyotes running around my fence line at night don't really want to cut loose with a shotgun or centerfire at midnight.Would like to keep it under a $1000 if possible.

This Scout is in perfect condition with a Huggett Astille moderator, Dedal Stalker scope and a custom RH English Walnut stock by Warren Snaith.
3 magazines included.
Maybe 1000 rounds through it if that.
After thorough testing and consult with Steyr the most accurate pellets to 100 yds are JSB Diabolo 14.35 gr.
$4900 shipped CONUS in original case, anywhere else actual shipping costs.

Has anybody tried to change the barrel on the Umarex Notos to a longer barrel? if so, where did you get the barrel from?
Thank you.

This Stoeger XM1 BullShark is a great little 27 inch long regulated PCP bullpup. It gets 50+ shots per fill in .22 with 15.89gr going 935 FPS. The JSB 18.1gr goes 894 FPS. The XM1 BullShark is a winner as far as I'm concerned. Thanks for watching! -Nate

Came on my We The Pilnkers package. Never used. Comes with pic rings.


Featuring a traditional 25mm (one inch) body tube to keep the weight down, the UltraLite’s lenses are treated with a superior multicoating to return light transmission figures almost identical to those of heavier, 30mm-tubed scopes in the same price bracket.

Besides its weight advantage, MTC Optics’ new Mamba 3-10×40 UltraLite boasts numerous other shooter-friendly specifications in its design, from its mil-dot reticle through its semi-target turrets, flip-up covers – complete with magnifier and side focus.

Features:
3-10x magnification range
40mm objective (superior multi-coating treatment)
Mil-dot reticle (true at 10x)
Semi-target turrets (1/4MOA). Finger-adjustable, with screw caps
Side focus, 10 yds to infinity
Magnetic flip-up covers, with 2x magnifier in ocular to easily view turret markings
Sidewheel parallax from 10 yds to infinity

$115 shipped PayPal f&f preferred or add 3.5% for g&s. Will ship to the lower 48

On a Regular Length Prophet I/II— What's the Biggest Bottle Possible

▪ Without preventing a large diameter silencer

▪ Without taking the shroud off


As I don't yet have a regular length Prophet I or II, I need to know the maximum length the bottle can have — in inches or cm.

It is highly unlikely I will buy a bottle from RTI.... — Maybe you even have a link to the AliExpress product?


Thanks,

Matthias

I'm probably going to regret this later, but I'm going to let my Rattler 357 go. I've had it since last year and have only shot it like twice. Just don't have the place to shoot it. It's basically new. I've recently got into archery and spend most of my free time shooting my bow. I'm asking 2200 shipped TYD. I'm open to offers. I've got plenty of great references on AGN. So deal with confidence. Can get better pictures later . Thanks for looking.

Yesterday I saw the post on UA blowing out RAW HM1000x chassis models, and then I noticed that a whole load of guns had been added to their 'Sale and Used' product category pages. More than I ever recall seeing on the UA site.

A lot of the guns are listed as used, some like the RAWs mentioned above are new, others are listed as demos, and still others are listed as 'open box' (which to me means likely discounted new old stock).

Judge for yourself if you see any bargains. I thought that the Caiman X in black wood/.25 cal/Gen1 for $699 was a deal so I grabbed it.

Good luck.

https://utahairguns.com/product-category/sale/used-products/used-airguns/

This is a one-off 24" .177 barrel that fits a first gen Taipan Veteran.

Lothar Walther, 1:17.7 with polygonal rifling. Slightly choked.

LW blank has been sleeved up to 15mm with carbon fiber and epoxied on brass end pieces.

Muzzle end has 1/2x20 threads and breech end has standard Taipan breech block threads.

Much lighter than full steel OEM barrel. Makes a Veteran balance very differently.

The carbon fiber sleeve consists of one piece that is 19.75" and a second piece that is 2.25" (see photo).

Due to the design of the Veteran, will work with a .22 Veteran or a .177 Veteran. Vets have extended pin probes so the larger diameter of the probe never makes it to the bore, so a .22 probe can be used with this .177 barrel. Vets also have a transfer port that is separate from the barrel, allowing you to use a .22 transfer port with a .177 barrel.

Please note that if using a .22 Veteran with this barrel, short .177 projectiles tip into the large dual transfer ports and make loading more difficult. If planning on dropping this into a .22 Veteran I'd recommend projectiles at least as long as a JSB 10.34.

$150 shipped. PayPal F&F or check/money order and we wait til the funds clear.

After the extraordinary experience of my Wolverines and Delta Wolf in .25 Cal with NSA 29 and 33.5 grain slugs, I decided to try the NSA 17.5 grain on my Red Wolf .22 Cal.

This Red Woof is EXTREMLY accurate with the H&N Barracudas. I am expecting to have same good accuracy at longer distance with the NSA 17.5 grain. The .25 NSA slugs are too heavy for that rifle, but they work great with the Wolverine HP HR .22 Cal.

As soon as I receive the slugs I will try them and will share the results.

brand new Alsafe
.42l cf tank for Sale
Not going to use 80 +shipping

Decided to open all ports contour and polish to a mirror finish wasn't easy
Also got a peek valve
Ported polished the poppet seat all ports 4.2mm
Except the new gauge block that's at 6mm
My scope only goes to 5mm
Otherwise I could show all the polishing
Here is a pic inside the block
Also 2 new hammers being machined
One will be able to add weight to inside by 1 gr at a time
Using Mallory for those
Should be done by Wed morning

As soon as the Altaron M24 was posted in the classified, I clicked on it and wondered a loooong time, if I should buy it.

The performance for extreme long range must be amazing.
The Altaros slugs have been made with this gun in mind, they come from the same brand.


But, in the end, I did not buy it.
However, I wanted to see how quickly it sells, considering that it is hard to even get it in the US.
➠ Surprise: It's still available on the classifieds....


And I wondered if my own reason for not buying it have something to do with why it hasn't sold yet.....

I like "black guns".
I like "modern looking guns" — not "traditional looking guns"
I like bullpups (less bulk, less weight, while same performance as traditional shape)
For a significant shotcount I want to attach a bottle (in the size that suits me)

And the Altaros checks NONE of those boxes .



𑇰 ••• I remember the designer and builder talking about being an engineer that engineers things that work good* (as opposed to things that also look good).

➠ Too bad.

Mora, here I come....

Matthias


PS: I hope it sells soon. It must be a gun that shoots amazingly.



See the WTS thread with photos here:


*for the English majors: "work well"

I'm just getting past the break-in period (about a tin of pellets) with my .22/600mm DRS and starting to look for the best pellet. Looks like the factory tuned to an 18g pellet.


Thought I'd share the numbers for anyone curious about the stability FX DRS.

JTS 18.1g -
A 911fps
H 914
L 910
ES 4
SD 1.7
FPE 33.3
GROUP (5 shots, 40 yards) .358 CTC

AA 18.0g -
A 916
H 919
L 914
ES 6
SD 2.2
FPE 33.5
GROUP .332 CTC

JSB 18.13g -
A 917
H 921
L 915
ES 7
SD 2.7
FPE 33.8
GROUP .338 CTC

I found that my DRS groups best with a light/loose hold.

Cheers!

Cannot Get some pellets into the barrel. Looks like the barrel was not cut centered and when closing the barrel it clips the pellet. Trying 14 to 18 grain pellets some will not go into barrel. Any suggestions or should I send it back?

LNIB Nightforce NX-8 4-32x50 rifle scope. The scope has only been used on a benchrest rifle - has never been out in the weather or used hunting. It is a FFP scope with ZeroStop and DigIllum reticle illumination. The fully illuminated MOAR reticle has 1 MOA hash marks. Includes NF labeled Tennebrax scope covers, 4 headed allen wrench for setting stops, cap on the windage turret, and I am including a Vortex cant level. Scope has no scratches or dings (see Photos).

I am asking $1400 to your door for this scope. I am not benchrest shooting anymore and want to move on. Willing to include the FX adjustable rings for another $50. PayPal FF preferred.

Ok thought I would share some of my BR observations. # 1- 5,6 yrs ago top guns shot from sighters “no flags” no need they said. Now almost all the top shot use them or read others.
# 2- almost all during that same time period only shot off bi-pods and a rear bag “if that” now most use a front rest or combination of bi-pod and rear rest to manipulate windage and elevation to a finite degree. This was not needed 5-6yrs ago according to the professionals.
#3- Note: these are just my observations and in no way dictates a winner from middle of the pack. Hell I used a rest and made the most stupid basic rookie mistake I shot 3 shots in a record bull because I didn’t drop down fully (I shoot bottom to top) and make sure I was on a sighter!!! I’ve shot both center fire BR and 25m BR so what does that say…

I went to an indoor range for the first time today - wanted to shoot with no wind. Set up at 50 yards with N50 practice targets. After sighting in I was hitting 10's and X's for most of the first 17 shots. The next two shots were almost outside the box and number 20 scored a 5. From that point on it was literally hit or miss with another 5, then 9, a wide 5, then 10, 10. Why in the world would this happen? Speeds were consistently in the 865~870 fps range. I'm shooting a .25 caliber R.A.W HM1000X (Rapid Air Worx) in an MPA frame. By the way, pellets were FX 34 grain weighed and sorted and also AEA Center Punch 33.9 grain.

Two more things - I believe R.A.W. sends these out at about 910~920 fps which seems too fast for Diabolo pellets so I tuned it back to 870-ish fps. Any thoughts on that as well? Also, adjusting the hammer spring has almost no affect on pellet speed. I know it's used for minor adjustments but fully out to fully in barely makes a 1-2 fps difference - bad hammer spring?

TIA for comments.